(01) — Cost guide · National edition
Siding Installation Cost in 2026
New siding is really two purchases in one: the cladding itself (vinyl, fiber cement or engineered wood) and the skilled labor that strips the old siding, wraps the walls, and hangs the new courses level and weathertight. Here is what residing a typical home actually costs in 2026 — per square foot, line by line, and set against the cost of doing it yourself.
- $6,500
- low end — simple spec, DIY-friendly scope
- $11,500
- typical — most homeowners pay near this
- $22,500
- high end — premium materials, complex site
- $7.50
- per sq ft of wall installed, typical vinyl siding
Typical project used for these figures: residing a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding, including house wrap, trim, and removal and disposal of the old siding. Ranges are 2026 US national averages for a professional installation unless stated.
What it costs, and why the range is wide
Most homeowners residing a typical US home in 2026 pay between $6,500 and $22,500, with a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding landing near $11,500 installed — about $7.50 per sq ft of wall. The spread is not arbitrary: the material runs roughly $3 to $10 per sq ft depending on what you choose, installation labor is about half of the total, and the condition of the walls underneath — rot, old siding removal, trim work — sets the ceiling. A straightforward vinyl job on a sound one-story home costs a fraction of a fiber cement job on a three-story house with rotted sheathing, for the same reason in both cases: the siding sets the floor, and the walls underneath set the ceiling.
The material is the first decision that moves the price. Vinyl is the budget baseline and the most common choice in the US: it costs $4 to $9 per sq ft installed, never needs painting, and lasts 20 to 40 years, but it can crack in extreme cold, warp in extreme heat, and melt near a grill or a reflective window. Fiber cement (James Hardie is the best-known brand) costs $6 to $14 per sq ft installed, holds paint for 10 to 15 years, resists fire, rot and insects, and lasts 30 to 50 years — it is the standard upgrade in wildfire and storm country. Engineered wood costs $5 to $11 per sq ft installed and looks like real wood without the maintenance, cedar runs $8 to $15, and aluminum $5 to $10. Work out your wall area first with the Square Footage Calculator — measure each wall's width by its height and subtract large openings — then price the job per square foot of wall, not per square foot of floor, because that is how siding is sold. Our siding buying guide compares the materials side by side and explains the warranties.
Removal is the second decision that moves the price. Stripping the old siding and disposing of it costs $1,000 to $3,000 on a typical home, and it is money well spent: it lets the crew inspect the sheathing, fix rot, and wrap the walls properly. Installing new siding over old siding saves the removal cost but hides whatever is rotting underneath, adds weight and thickness that complicates trim and window flashing, and voids the warranty on several fiber cement products. If your home was built before 1978, budget for lead-paint rules too — disturbing painted siding on an older home requires EPA RRP-certified work, which adds $500 to $1,500. Check whether your utility or state offers an energy rebate for insulated siding, because several do, and fold the whole project into your budget with the Renovation Budget Calculator.
Cost breakdown: where the money goes
For the typical project — residing a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding, including house wrap, trim, and removal and disposal of the old siding — the job usually builds up like this:
| Line item | Materials | Labor | Total |
|---|---|---|---|
| Vinyl siding material — 1,500 sq ft plus wasteStandard vinyl siding panels, starter strip, J-channel and corner posts, with a 10 percent waste allowance for cuts | $4,200 | $0 | $4,200 |
| House wrap and flashingHouse wrap over the sheathing, taped seams, and flashing tape at windows, doors and penetrations | $450 | $350 | $800 |
| Removal and disposal of old sidingStrip the old siding, haul it away, and dispose of it under local rules, including lead-paint handling where required | $50 | $1,200 | $1,250 |
| Installation labor — hang, level and fastenHang the courses level with the correct expansion gap, nail into studs, and cut and fit around windows, doors and fixtures | $0 | $3,850 | $3,850 |
| Trim, soffit and fasciaCorner boards, window and door trim, soffit panels and fascia boards, matched to the new siding | $650 | $550 | $1,200 |
| Delivery and permitsMaterial delivery and the building permit where the jurisdiction requires one | $200 | $0 | $200 |
| Total for a typical residing job1,500 sq ft of wall in vinyl siding — about $11,500 | $5,550 | $5,950 | $11,500 |
Materials and labor are split the way contractors build a quote, so you can compare a real bid line by line. Figures are for the typical project above and will move with your spec — the next sections explain what moves them.
Cost by siding material
Material choice moves the price more than house size does — fiber cement on the same walls costs roughly 40 percent more than vinyl, because both the material and the labor are heavier. Prices below are installed, per sq ft of wall, for a typical home.
| Material | Per sq ft installed | 1,500 sq ft home | Best for |
|---|---|---|---|
| Vinyl | $4 – $9 | $6,000 – $13,500 | Most US homes — the best value, no painting, 20 to 40 year lifespan; avoid dark colors in extreme heat and keep grills away from the wall |
| Fiber cement | $6 – $14 | $9,000 – $21,000 | Wildfire and storm country, and homes where a painted look matters — fire, rot and insect resistant, holds paint 10 to 15 years, 30 to 50 year lifespan |
| Engineered wood | $5 – $11 | $7,500 – $16,500 | The look of real wood without the maintenance — lighter than fiber cement, easier to cut and install, needs repainting every 10 to 15 years |
| Cedar / natural wood | $8 – $15 | $12,000 – $22,500 | Traditional and high-end homes where appearance is the priority — beautiful, but needs staining or painting every 3 to 5 years and is vulnerable to rot and insects |
| Aluminum / steel | $5 – $10 | $7,500 – $15,000 | Fire-prone areas and homes that need a dent-resistant, low-maintenance skin — steel is the tougher of the two; aluminum dents more easily |
Work out your wall area first with the Square Footage Calculator — and read the siding buying guide before you order, because it explains when vinyl is the right call and when fiber cement earns its premium. If the walls underneath are in bad shape, check the drywall installation cost guide too, since rot found during a residing job often means interior wall work as well.
What a standard quote includes — and what it leaves out
Usually included
- The siding to the agreed specification — panels, starter strip, J-channel, corner posts and fasteners, matched to the wall area plus waste
- Installation labor: hanging the courses level, nailing into studs with the correct expansion gap, and cutting and fitting around windows, doors and fixtures
- House wrap over the sheathing with taped seams, and flashing tape at windows, doors and penetrations
- Trim, soffit and fascia boards matched to the new siding, where the quote includes them
- Removal of the old siding and haul-away and disposal, including lead-paint handling where required
- The building permit and the final inspection, where the quote includes them
Commonly billed as extras
- Sheathing and framing repair — rot found once the old siding is off is carpentry, not siding work, and is priced separately, typically $500 to $3,000 depending on the extent
- Insulation upgrades — adding rigid foam board under the siding improves energy performance but adds $1 to $2 per sq ft, and is a separate line
- Painting — vinyl needs none, but fiber cement, engineered wood and cedar need a finish coat, and factory-primed boards still need painting on site
- Gutters and downspouts — these usually come off during a residing job and may need rehanging or replacement, priced separately
- Lead-paint abatement beyond disposal — homes built before 1978 may need EPA RRP-certified work, which adds $500 to $1,500
- Scaffolding or lift rental — second- and third-story walls on a home with no safe ladder access may need a lift, priced separately
DIY or hire a pro?
Vinyl siding is one of the more DIY-able exterior projects: the panels are light, they lock together, and a mistake costs one pulled course, not a ruined wall. A skilled homeowner with a level, a snap-lock punch and a circular saw can side a one-story garage or a small single-story wall in a weekend, and the savings are real — roughly $3,500 to $4,000 of labor on the typical home. The work that decides the result is the unglamorous part: the house wrap, the flashing at every window and door, and the expansion gap at every panel end, because vinyl moves with temperature and a course nailed tight will buckle in the first hot summer.
Fiber cement is a different job and belongs to a professional: the boards are heavy, they need a specialized saw and dust control (the dust contains silica), and the cutting, nailing pattern and clearances are exact — a board cut wrong or nailed wrong cracks, and the warranty depends on the installation following the manufacturer specification. The sensible split is to DIY vinyl on accessible single-story walls when the sheathing is sound, and hire a licensed installer for fiber cement, second-story work, homes with rot, and any home built before 1978, where lead-paint rules apply. Whatever you do, never caulk the bottom edge of vinyl siding — it needs to drain — and always leave the manufacturer expansion gap at the panel ends, because a course installed tight in winter will oil-can by July.
Honest difficulty rating: Vinyl siding is DIY-able for a skilled homeowner on accessible single-story walls with sound sheathing; fiber cement, second-story work, rot repair and pre-1978 homes (lead paint) belong to a professional installer.
What drives the cost up or down
- Material choice. Vinyl is the budget baseline at $4 to $9 per sq ft installed; fiber cement runs $6 to $14 and cedar $8 to $15, for the same walls. Fiber cement earns its premium in wildfire and storm country and where a painted look matters; cedar earns it on traditional homes, where the wrong cladding costs more in resale value than the saving on vinyl.
- Wall area and stories. Siding is priced per square foot of wall, so a two-story home costs more per square foot of floor than a one-story home — more wall, more cutting, more ladder and scaffold time. A 2,000 sq ft two-story home has about 1,500 sq ft of wall; a 2,000 sq ft ranch has about 1,200 sq ft but a longer perimeter. Measure walls, not floors.
- Old siding removal and wall condition. Stripping and disposing of old siding costs $1,000 to $3,000, and what the crew finds underneath decides the rest of the bill. Rot, failed sheathing and insect damage are all priced separately, and a home that has had siding over siding for decades can hide a five-figure repair. Budget 10 percent for wall repair on any home over 30 years old.
- Trim, soffit and fascia. Trim work is where quotes quietly differ: corner boards, window and door trim, soffit and fascia can add $1,000 to $2,500 to a typical job, and a quote that omits them is not comparable to one that includes them. Confirm in writing whether the quote covers full trim replacement or reuse of the existing trim.
- Climate and code. Wildfire zones require noncombustible cladding or ember-resistant assemblies; hurricane zones require wind-rated fastening; cold climates punish vinyl that gets brittle and fiber cement that is cut without the right clearances. Local code also decides the permit: some jurisdictions require a permit for any residing job, others only above a threshold.
- Rot, lead paint and access. Rot found after removal, lead-paint rules on pre-1978 homes, and second- or third-story walls that need scaffolding or a lift are the three items that turn a fixed quote into a change order. Confirm in writing whether the quote includes lead-safe work and lift rental, and ask what the per-sheet sheathing replacement price is before the old siding comes off.
How to keep the cost down
- Measure the walls yourself with the Square Footage Calculator before you get quotes — a contractor who prices from floor area instead of wall area is pricing a different job.
- Compare quotes on the same specification: material, wall area, house wrap, flashing, trim, soffit and fascia, removal and disposal, permit — each named.
- Ask for the per-sheet sheathing replacement price in writing before the old siding comes off, so rot found mid-job has an agreed price, not a surprise.
- Check the expansion gap: vinyl panels need room to move with temperature, and a course nailed tight will buckle in the first hot summer.
- Never caulk the bottom edge of vinyl siding — it needs to drain. Water that gets behind siding must have a way out.
- Keep a few spare panels from the same production run in the garage. Colors drift between runs, and a future repair with a mismatched panel shows forever.
Frequently asked questions
Residing a 2,000 sq ft two-story home — about 1,500 sq ft of wall area — costs about $11,500 in vinyl siding in 2026, with most jobs landing between $6,500 and $22,500. Fiber cement on the same walls runs about $9,000 to $21,000, engineered wood $7,500 to $16,500, and cedar $12,000 to $22,500. The material, the wall condition underneath and the trim work set the final price.
Vinyl is cheaper upfront ($4 to $9 per sq ft installed vs $6 to $14 for fiber cement) and never needs painting, with a 20 to 40 year lifespan. Fiber cement costs more, holds paint 10 to 15 years, resists fire, rot and insects, and lasts 30 to 50 years. Over a 30-year life, fiber cement is usually the better value in wildfire and storm country and on homes where a painted look matters; vinyl wins on upfront budget and in mild climates.
You can install vinyl over some old siding, but it is usually a false economy. It saves the $1,000 to $3,000 removal cost, but it hides whatever is rotting underneath, adds thickness that complicates trim and window flashing, and voids the warranty on several fiber cement products. Stripping the old siding lets the crew inspect the sheathing, fix rot and wrap the walls properly — the work that decides whether the new siding lasts 30 years or 10.
Vinyl siding lasts 20 to 40 years, fiber cement 30 to 50 years, engineered wood 20 to 30 years, cedar 20 to 40 years with regular maintenance, and aluminum or steel 40 years or more. Lifespan depends on installation quality as much as material: siding hung without proper flashing and expansion gaps fails early whatever it is made of.
A professional crew resids a typical 2,000 sq ft home in 5 to 10 working days: a day or two of removal and wrap, 3 to 5 days of hanging, and a day of trim and cleanup. Fiber cement takes longer than vinyl because the boards are heavier and slower to cut. DIY vinyl on a one-story home, plan on two to three weekends.
It depends on the jurisdiction. Many cities require a building permit for any residing job, others only when the work is structural or changes the exterior appearance, and some require nothing for a like-for-like replacement. Wildfire and hurricane zones add their own requirements. Check with your local building department before the crew starts — a permit costs $100 to $300 and an unpermitted job can stall a home sale.
Yes. New siding is one of the highest-return exterior projects: industry cost-vs-value data puts vinyl siding replacement at roughly 70 to 80 percent of its cost recovered at resale, and fiber cement higher, because curb appeal is the first thing a buyer prices. The return is highest when the old siding is visibly failing — stained, warped, or rotting — and lowest when the existing siding is sound and the job is purely cosmetic.
Cost by state
Labor is the part of the price that moves most by location. These state editions re-price this guide with the local labor index, add city prices and the state-specific permit and code notes.
Siding Installation Cost in Texas
State-adjusted prices, city figures and Texas code notes.
Read the guideSiding Installation Cost in California
State-adjusted prices, city figures and California code notes.
Read the guideSiding Installation Cost in Florida
State-adjusted prices, city figures and Florida code notes.
Read the guideSiding Installation Cost in New York
State-adjusted prices, city figures and New York code notes.
Read the guideSiding Installation Cost in Pennsylvania
State-adjusted prices, city figures and Pennsylvania code notes.
Read the guideSiding Installation Cost in Illinois
State-adjusted prices, city figures and Illinois code notes.
Read the guideSiding Installation Cost in Ohio
State-adjusted prices, city figures and Ohio code notes.
Read the guideSiding Installation Cost in Georgia
State-adjusted prices, city figures and Georgia code notes.
Read the guideSiding Installation Cost in North Carolina
State-adjusted prices, city figures and North Carolina code notes.
Read the guideSiding Installation Cost in Michigan
State-adjusted prices, city figures and Michigan code notes.
Read the guideMore cost guides
Deck Build Cost
Materials and labor for a ground-level deck in pressure-treated lumber, cedar and composite, priced per square foot with railing and stair allowances.
Read the guideRoof Replacement Cost
Tear-off and replacement per roofing square for architectural shingles, metal and tile, including underlayment, flashing and disposal.
Read the guideBathroom Remodel Cost
Full and partial remodels at three finish levels, split between fixtures, tile, plumbing, electrical and labor.
Read the guide