(01) — Cost guide · North Carolina edition
Siding Installation Cost in North Carolina (2026)
In North Carolina, siding installation cost for the typical project costs about $11,150 — 3% below the national average of $11,500. The gap comes from labor: North Carolina labor runs at 0.94× the national average, and labor is about 50% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the North Carolina numbers, city prices and code notes.
- $6,300
- low end in North Carolina — simple spec
- $11,150
- typical in North Carolina — most homeowners pay near this
- $21,850
- high end in North Carolina — premium materials, complex site
- $7.27
- per sq ft of wall installed, typical vinyl siding, North Carolina-adjusted
Typical project used for these figures: residing a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding, including house wrap, trim, and removal and disposal of the old siding. Ranges are 2026 planning figures for a professional installation in North Carolina, derived from the national guide as explained below — always confirm with local quotes.
North Carolina prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and North Carolina labor sits at 0.94× the national average. Applying that index to the labor share (about 50% of the installed price) gives the North Carolina range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | North Carolina | Difference |
|---|---|---|---|
| Low end | $6,500 | $6,300 | 3% below |
| Typical project | $11,500 | $11,150 | 3% below |
| High end | $22,500 | $21,850 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national siding installation cost guide. The table below re-prices that same breakdown for North Carolina.
Cost breakdown, North Carolina-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the North Carolina index of 0.94. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (North Carolina) | Total |
|---|---|---|---|
| Vinyl siding material — 1,500 sq ft plus wasteStandard vinyl siding panels, starter strip, J-channel and corner posts, with a 10 percent waste allowance for cuts | $4,200 | $0 | $4,200 |
| House wrap and flashingHouse wrap over the sheathing, taped seams, and flashing tape at windows, doors and penetrations | $450 | $350 | $800 |
| Removal and disposal of old sidingStrip the old siding, haul it away, and dispose of it under local rules, including lead-paint handling where required | $50 | $1,150 | $1,200 |
| Installation labor — hang, level and fastenHang the courses level with the correct expansion gap, nail into studs, and cut and fit around windows, doors and fixtures | $0 | $3,600 | $3,600 |
| Trim, soffit and fasciaCorner boards, window and door trim, soffit panels and fascia boards, matched to the new siding | $650 | $500 | $1,150 |
| Delivery and permitsMaterial delivery and the building permit where the jurisdiction requires one | $200 | $0 | $200 |
| Total for the typical projectState-adjusted from the national breakdown above | $5,550 | $5,600 | $11,150 |
Typical cost by city in North Carolina
Labor markets differ within a state too. These city figures apply each city's multiplier to the North Carolina typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Greensboro | $10,700 |
| Winston-Salem | $10,700 |
| Durham | $11,150 |
| Wilmington | $11,150 |
| Charlotte | $11,400 |
| Raleigh | $11,600 |
North Carolina rules, climate and code that change the price
North Carolina's code is statewide (the NC Residential Code) with local enforcement, and its geography splits costs: the mountains need deeper frost footings and snow consideration, the Piedmont is moderate, and the coast carries hurricane wind requirements. Frost depth is about 12–18 in in the Piedmont and deeper in the mountains. The Research Triangle and Charlotte are the state's higher-cost metros, while coastal wind detailing adds cost in the east even though labor there is average.
Siding Installation Cost in North Carolina: what to watch
How much does siding installation cost in North Carolina? A typical 2,000 sq ft two-story home (about 1,500 sq ft of wall) in vinyl siding runs about $11,150 — just below the national typical of $11,500, with most North Carolina jobs landing between $6,300 and $21,850. Charlotte runs about $11,350 and Raleigh about $11,600. North Carolina siding spans three climates: coastal wind detailing and salt corrosion in the east, moderate Piedmont conditions around Charlotte and Raleigh, and deeper frost and snow in the mountains. Coastal homes need wind-rated fastening and corrosion-resistant trim, mountain homes need siding that tolerates freeze-thaw, and the Piedmont sits in between. The NC Residential Code applies statewide with local enforcement, and the Research Triangle and Charlotte are the state's higher-cost metros. Match the material to your region — fiber cement earns its premium on the coast and in the mountains, while vinyl is the value choice in the Piedmont.
What to ask contractors in North Carolina
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: North Carolina requires permits for roofing, decks and structural work in every county under the state residential code. Coastal counties add wind-borne debris and uplift requirements that the permit review checks on roofing and deck connections.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the North Carolina labor market: a quote far above the $11,150 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — North Carolina
North Carolina requires permits for roofing, decks and structural work in every county under the state residential code. Coastal counties add wind-borne debris and uplift requirements that the permit review checks on roofing and deck connections.
North Carolina labor runs about 6% below the national average, with Raleigh and Charlotte slightly above the state figure. Mountain frost footings and coastal wind detailing are the two regional adders that national averages do not capture.
Budget around $11,150 for the typical project (residing a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding, including house wrap, trim, and removal and disposal of the old siding) in North Carolina, with most jobs landing between $6,300 and $21,850. That typical figure is 3% below the national typical of $11,500, because North Carolina labor runs at 0.94× the national average and labor is about 50% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within North Carolina, the typical project runs from about $10,700 in Greensboro to about $11,600 in Raleigh, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.