(01) — Cost guide · Pennsylvania edition
Siding Installation Cost in Pennsylvania (2026)
In Pennsylvania, siding installation cost for the typical project costs about $11,600 — 1% above the national average of $11,500. The gap comes from labor: Pennsylvania labor runs at 1.02× the national average, and labor is about 50% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Pennsylvania numbers, city prices and code notes.
- $6,550
- low end in Pennsylvania — simple spec
- $11,600
- typical in Pennsylvania — most homeowners pay near this
- $22,750
- high end in Pennsylvania — premium materials, complex site
- $7.58
- per sq ft of wall installed, typical vinyl siding, Pennsylvania-adjusted
Typical project used for these figures: residing a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding, including house wrap, trim, and removal and disposal of the old siding. Ranges are 2026 planning figures for a professional installation in Pennsylvania, derived from the national guide as explained below — always confirm with local quotes.
Pennsylvania prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Pennsylvania labor sits at 1.02× the national average. Applying that index to the labor share (about 50% of the installed price) gives the Pennsylvania range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Pennsylvania | Difference |
|---|---|---|---|
| Low end | $6,500 | $6,550 | 1% above |
| Typical project | $11,500 | $11,600 | 1% above |
| High end | $22,500 | $22,750 | 1% above |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national siding installation cost guide. The table below re-prices that same breakdown for Pennsylvania.
Cost breakdown, Pennsylvania-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Pennsylvania index of 1.02. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Pennsylvania) | Total |
|---|---|---|---|
| Vinyl siding material — 1,500 sq ft plus wasteStandard vinyl siding panels, starter strip, J-channel and corner posts, with a 10 percent waste allowance for cuts | $4,200 | $0 | $4,200 |
| House wrap and flashingHouse wrap over the sheathing, taped seams, and flashing tape at windows, doors and penetrations | $450 | $350 | $800 |
| Removal and disposal of old sidingStrip the old siding, haul it away, and dispose of it under local rules, including lead-paint handling where required | $50 | $1,200 | $1,250 |
| Installation labor — hang, level and fastenHang the courses level with the correct expansion gap, nail into studs, and cut and fit around windows, doors and fixtures | $0 | $3,950 | $3,950 |
| Trim, soffit and fasciaCorner boards, window and door trim, soffit panels and fascia boards, matched to the new siding | $650 | $550 | $1,200 |
| Delivery and permitsMaterial delivery and the building permit where the jurisdiction requires one | $200 | $0 | $200 |
| Total for the typical projectState-adjusted from the national breakdown above | $5,550 | $6,050 | $11,600 |
Typical cost by city in Pennsylvania
Labor markets differ within a state too. These city figures apply each city's multiplier to the Pennsylvania typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Erie | $10,700 |
| Scranton | $10,700 |
| Harrisburg | $11,150 |
| Allentown | $11,400 |
| Pittsburgh | $11,600 |
| Philadelphia | $12,300 |
Pennsylvania rules, climate and code that change the price
Pennsylvania follows the Uniform Construction Code statewide, but enforcement sits with municipalities, so permit practice and inspection rigour vary between Philadelphia, Pittsburgh and small townships. Frost depth runs 36–42 in across much of the state, so footings for decks, fences and porches must go well below grade, and snow loads in the northern tier and the Alleghenies affect roof and deck design. Philadelphia adds its own licensing and permit layers on top of the state code.
Siding Installation Cost in Pennsylvania: what to watch
Pennsylvania siding is an older-stock job. Residing a typical 2,000 sq ft home runs about $11,600 in vinyl — close to the national typical of $11,500 — with Philadelphia about $12,300 and Erie about $10,650. Philadelphia row houses and Pittsburgh century homes often hold original wood siding with rot at the sill and bottom courses, so a residing quote frequently grows once the old siding is off — budget for sheathing repair rather than discovering it mid-job. Pre-1978 homes carry lead paint risk, so disturbing painted siding requires EPA RRP-certified work. The Uniform Construction Code applies statewide with municipal enforcement, so permit practice varies, and Philadelphia adds its own licensing layers — confirm whether your municipality requires a permit before ordering.
What to ask contractors in Pennsylvania
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Pennsylvania municipalities enforce the Uniform Construction Code locally, so permit requirements for roofing, decks and remodels are near-universal but the office, fees and inspection schedule depend on the municipality. Philadelphia has additional licensing and permit requirements beyond the state code.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Pennsylvania labor market: a quote far above the $11,600 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Pennsylvania
Pennsylvania municipalities enforce the Uniform Construction Code locally, so permit requirements for roofing, decks and remodels are near-universal but the office, fees and inspection schedule depend on the municipality. Philadelphia has additional licensing and permit requirements beyond the state code.
Pennsylvania labor sits close to the national average, with Philadelphia about 6% above the state figure. The cost items that surprise newcomers are deep frost footings and snow-load structure, both of which are standard here and absent from warm-climate pricing.
Budget around $11,600 for the typical project (residing a 2,000 sq ft two-story home (about 1,500 sq ft of wall area) in vinyl siding, including house wrap, trim, and removal and disposal of the old siding) in Pennsylvania, with most jobs landing between $6,550 and $22,750. That typical figure is 1% above the national typical of $11,500, because Pennsylvania labor runs at 1.02× the national average and labor is about 50% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Pennsylvania, the typical project runs from about $10,700 in Erie to about $12,300 in Philadelphia, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.