(01) — Cost guide · Texas edition
Patio Cost in Texas (2026)
In Texas, patio cost for the typical project costs about $5,250 — 3% below the national average of $5,400. The gap comes from labor: Texas labor runs at 0.94× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Texas numbers, city prices and code notes.
- $2,550
- low end in Texas — simple spec
- $5,250
- typical in Texas — most homeowners pay near this
- $10,900
- high end in Texas — premium materials, complex site
- $16.54
- per sq ft installed, typical concrete-paver patio, Texas-adjusted
Typical project used for these figures: a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground. Ranges are 2026 planning figures for a professional installation in Texas, derived from the national guide as explained below — always confirm with local quotes.
Texas prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Texas labor sits at 0.94× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Texas range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Texas | Difference |
|---|---|---|---|
| Low end | $2,600 | $2,550 | 3% below |
| Typical project | $5,400 | $5,250 | 3% below |
| High end | $11,200 | $10,900 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national patio cost guide. The table below re-prices that same breakdown for Texas.
Cost breakdown, Texas-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Texas index of 0.94. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Texas) | Total |
|---|---|---|---|
| Excavation & gradingDigging 7–9 in deep, grading for drainage fall away from the house, hauling spoil | $50 | $400 | $450 |
| Gravel base & beddingAbout 4–6 in of compacted crushed stone plus a 1 in screeded bedding-sand layer | $650 | $400 | $1,050 |
| Pavers320 sq ft of standard concrete pavers including the waste allowance for cuts | $1,750 | $0 | $1,750 |
| Laying & jointing laborSetting the field and border, cutting edges, compacting and sweeping joints | $0 | $1,100 | $1,100 |
| Edge restraints & cutsSpiked edge restraint on all open sides; diamond-blade cuts at borders and obstacles | $250 | $250 | $500 |
| Joint sand, sealer & cleanupPolymeric joint sand, optional sealer coat, wash-down and site cleanup | $200 | $150 | $350 |
| Delivery & permitsMaterial delivery and permit where the jurisdiction requires one | $50 | $0 | $50 |
| Total for the typical projectState-adjusted from the national breakdown above | $2,950 | $2,300 | $5,250 |
Typical cost by city in Texas
Labor markets differ within a state too. These city figures apply each city's multiplier to the Texas typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| El Paso | $4,750 |
| San Antonio | $5,050 |
| Fort Worth | $5,150 |
| Houston | $5,250 |
| Dallas | $5,350 |
| Austin | $5,650 |
Texas rules, climate and code that change the price
Texas has no statewide general-contractor license, so permit rules and inspection quality vary by city — Houston, Dallas and Austin all run their own permitting portals with different thresholds, and unincorporated areas may require no building permit at all. Frost depth is shallow across most of the state (often 6–12 in), which keeps footing work cheap, but expansive clay soils around Dallas–Fort Worth and Houston move with moisture and demand deeper, belled piers for decks and fences. Gulf Coast wind and hail exposure raises roofing and fence specifications, and hail-resistant shingles are a common insurance-driven upgrade.
Patio Cost in Texas: what to watch
Texas patio building is a heat and clay job. A typical 16 × 20 ft paver patio runs about $5,250 — just under the national typical of $5,400 — with Austin about $5,650 and El Paso about $4,750. Light-colored pavers and stone are worth specifying, because dark surfaces get too hot to walk on barefoot through a Texas summer, and the base is where Texas quotes differ: expansive clay soils around Dallas-Fort Worth and Houston need a deeper compacted base, and a patio built on a thin base on clay heaves and ripples within two winters. There is no statewide contractor license, so permit rules vary by city, and an at-grade patio usually needs no permit — but drainage does matter, because a patio that sheds water toward the house is a foundation problem on clay.
What to ask contractors in Texas
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Most Texas cities require a permit for a roof replacement, a deck over 30 in high or attached to the house, and any structural work, but thresholds differ by city and unincorporated land often has none. Check the city permitting portal before work starts — an unpermitted deck or roof can stall a future sale even where enforcement is light.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Texas labor market: a quote far above the $5,250 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Texas
Most Texas cities require a permit for a roof replacement, a deck over 30 in high or attached to the house, and any structural work, but thresholds differ by city and unincorporated land often has none. Check the city permitting portal before work starts — an unpermitted deck or roof can stall a future sale even where enforcement is light.
Texas labor runs about 6% below the national average, so installed prices sit slightly under national figures, but Austin runs roughly 8% above the state figure and Gulf Coast wind/hail specifications can erase the saving on roofing. Material prices are national; it is the labor line and the local code extras that move a Texas quote.
Budget around $5,250 for the typical project (a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground) in Texas, with most jobs landing between $2,550 and $10,900. That typical figure is 3% below the national typical of $5,400, because Texas labor runs at 0.94× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Texas, the typical project runs from about $4,750 in El Paso to about $5,650 in Austin, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.