(01) — Cost guide · Pennsylvania edition
Patio Cost in Pennsylvania (2026)
In Pennsylvania, patio cost for the typical project costs about $5,450 — 1% above the national average of $5,400. The gap comes from labor: Pennsylvania labor runs at 1.02× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Pennsylvania numbers, city prices and code notes.
- $2,600
- low end in Pennsylvania — simple spec
- $5,450
- typical in Pennsylvania — most homeowners pay near this
- $11,300
- high end in Pennsylvania — premium materials, complex site
- $17.15
- per sq ft installed, typical concrete-paver patio, Pennsylvania-adjusted
Typical project used for these figures: a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground. Ranges are 2026 planning figures for a professional installation in Pennsylvania, derived from the national guide as explained below — always confirm with local quotes.
Pennsylvania prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Pennsylvania labor sits at 1.02× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Pennsylvania range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Pennsylvania | Difference |
|---|---|---|---|
| Low end | $2,600 | $2,600 | 1% above |
| Typical project | $5,400 | $5,450 | 1% above |
| High end | $11,200 | $11,300 | 1% above |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national patio cost guide. The table below re-prices that same breakdown for Pennsylvania.
Cost breakdown, Pennsylvania-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Pennsylvania index of 1.02. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Pennsylvania) | Total |
|---|---|---|---|
| Excavation & gradingDigging 7–9 in deep, grading for drainage fall away from the house, hauling spoil | $50 | $450 | $500 |
| Gravel base & beddingAbout 4–6 in of compacted crushed stone plus a 1 in screeded bedding-sand layer | $650 | $400 | $1,050 |
| Pavers320 sq ft of standard concrete pavers including the waste allowance for cuts | $1,750 | $0 | $1,750 |
| Laying & jointing laborSetting the field and border, cutting edges, compacting and sweeping joints | $0 | $1,150 | $1,150 |
| Edge restraints & cutsSpiked edge restraint on all open sides; diamond-blade cuts at borders and obstacles | $250 | $250 | $500 |
| Joint sand, sealer & cleanupPolymeric joint sand, optional sealer coat, wash-down and site cleanup | $200 | $200 | $400 |
| Delivery & permitsMaterial delivery and permit where the jurisdiction requires one | $50 | $0 | $50 |
| Total for the typical projectState-adjusted from the national breakdown above | $2,950 | $2,500 | $5,450 |
Typical cost by city in Pennsylvania
Labor markets differ within a state too. These city figures apply each city's multiplier to the Pennsylvania typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Erie | $5,000 |
| Scranton | $5,000 |
| Harrisburg | $5,250 |
| Allentown | $5,350 |
| Pittsburgh | $5,450 |
| Philadelphia | $5,800 |
Pennsylvania rules, climate and code that change the price
Pennsylvania follows the Uniform Construction Code statewide, but enforcement sits with municipalities, so permit practice and inspection rigour vary between Philadelphia, Pittsburgh and small townships. Frost depth runs 36–42 in across much of the state, so footings for decks, fences and porches must go well below grade, and snow loads in the northern tier and the Alleghenies affect roof and deck design. Philadelphia adds its own licensing and permit layers on top of the state code.
Patio Cost in Pennsylvania: what to watch
Pennsylvania patio building is a freeze-thaw and older-stock job. A typical 16 × 20 ft paver patio runs about $5,450 — close to the national typical of $5,400 — with Philadelphia about $5,800 and Erie about $5,000. Frost depth of 36–42 in means the base must be properly compacted and deep enough to resist heaving, and the state's older homes often mean a patio is built against a stone foundation that needs the fall directed away from it. Flagstone and bluestone are the traditional Pennsylvania surfaces and suit the state's older homes, but they cost more to lay than concrete pavers because irregular stone is slower to set. The Uniform Construction Code applies statewide with municipal enforcement, so check whether your township requires a permit for a patio with a retaining edge or drainage work.
What to ask contractors in Pennsylvania
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Pennsylvania municipalities enforce the Uniform Construction Code locally, so permit requirements for roofing, decks and remodels are near-universal but the office, fees and inspection schedule depend on the municipality. Philadelphia has additional licensing and permit requirements beyond the state code.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Pennsylvania labor market: a quote far above the $5,450 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Pennsylvania
Pennsylvania municipalities enforce the Uniform Construction Code locally, so permit requirements for roofing, decks and remodels are near-universal but the office, fees and inspection schedule depend on the municipality. Philadelphia has additional licensing and permit requirements beyond the state code.
Pennsylvania labor sits close to the national average, with Philadelphia about 6% above the state figure. The cost items that surprise newcomers are deep frost footings and snow-load structure, both of which are standard here and absent from warm-climate pricing.
Budget around $5,450 for the typical project (a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground) in Pennsylvania, with most jobs landing between $2,600 and $11,300. That typical figure is 1% above the national typical of $5,400, because Pennsylvania labor runs at 1.02× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Pennsylvania, the typical project runs from about $5,000 in Erie to about $5,800 in Philadelphia, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.