(01) — Cost guide · North Carolina edition
Patio Cost in North Carolina (2026)
In North Carolina, patio cost for the typical project costs about $5,250 — 3% below the national average of $5,400. The gap comes from labor: North Carolina labor runs at 0.94× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the North Carolina numbers, city prices and code notes.
- $2,550
- low end in North Carolina — simple spec
- $5,250
- typical in North Carolina — most homeowners pay near this
- $10,900
- high end in North Carolina — premium materials, complex site
- $16.54
- per sq ft installed, typical concrete-paver patio, North Carolina-adjusted
Typical project used for these figures: a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground. Ranges are 2026 planning figures for a professional installation in North Carolina, derived from the national guide as explained below — always confirm with local quotes.
North Carolina prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and North Carolina labor sits at 0.94× the national average. Applying that index to the labor share (about 45% of the installed price) gives the North Carolina range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | North Carolina | Difference |
|---|---|---|---|
| Low end | $2,600 | $2,550 | 3% below |
| Typical project | $5,400 | $5,250 | 3% below |
| High end | $11,200 | $10,900 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national patio cost guide. The table below re-prices that same breakdown for North Carolina.
Cost breakdown, North Carolina-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the North Carolina index of 0.94. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (North Carolina) | Total |
|---|---|---|---|
| Excavation & gradingDigging 7–9 in deep, grading for drainage fall away from the house, hauling spoil | $50 | $400 | $450 |
| Gravel base & beddingAbout 4–6 in of compacted crushed stone plus a 1 in screeded bedding-sand layer | $650 | $400 | $1,050 |
| Pavers320 sq ft of standard concrete pavers including the waste allowance for cuts | $1,750 | $0 | $1,750 |
| Laying & jointing laborSetting the field and border, cutting edges, compacting and sweeping joints | $0 | $1,100 | $1,100 |
| Edge restraints & cutsSpiked edge restraint on all open sides; diamond-blade cuts at borders and obstacles | $250 | $250 | $500 |
| Joint sand, sealer & cleanupPolymeric joint sand, optional sealer coat, wash-down and site cleanup | $200 | $150 | $350 |
| Delivery & permitsMaterial delivery and permit where the jurisdiction requires one | $50 | $0 | $50 |
| Total for the typical projectState-adjusted from the national breakdown above | $2,950 | $2,300 | $5,250 |
Typical cost by city in North Carolina
Labor markets differ within a state too. These city figures apply each city's multiplier to the North Carolina typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Greensboro | $5,050 |
| Winston-Salem | $5,050 |
| Durham | $5,250 |
| Wilmington | $5,250 |
| Charlotte | $5,350 |
| Raleigh | $5,450 |
North Carolina rules, climate and code that change the price
North Carolina's code is statewide (the NC Residential Code) with local enforcement, and its geography splits costs: the mountains need deeper frost footings and snow consideration, the Piedmont is moderate, and the coast carries hurricane wind requirements. Frost depth is about 12–18 in in the Piedmont and deeper in the mountains. The Research Triangle and Charlotte are the state's higher-cost metros, while coastal wind detailing adds cost in the east even though labor there is average.
Patio Cost in North Carolina: what to watch
North Carolina patio building spans three climates, and the base follows the geography. A typical 16 × 20 ft paver patio runs about $5,250 — just under the national typical of $5,400 — with Raleigh about $5,450 and Charlotte about $5,350. The mountains need a deeper base for frost and snow, the Piedmont is moderate, and the coast is a drainage and sand job where the base must resist washout from heavy rain and storm surge is a planning factor for low-lying lots. The statewide residential code means permit practice is consistent, with coastal counties adding wind and flood-zone checks that can affect any retaining edge or drainage work. Humidity grows algae on shaded pavers statewide, so a sealer coat is worth pricing.
What to ask contractors in North Carolina
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: North Carolina requires permits for roofing, decks and structural work in every county under the state residential code. Coastal counties add wind-borne debris and uplift requirements that the permit review checks on roofing and deck connections.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the North Carolina labor market: a quote far above the $5,250 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — North Carolina
North Carolina requires permits for roofing, decks and structural work in every county under the state residential code. Coastal counties add wind-borne debris and uplift requirements that the permit review checks on roofing and deck connections.
North Carolina labor runs about 6% below the national average, with Raleigh and Charlotte slightly above the state figure. Mountain frost footings and coastal wind detailing are the two regional adders that national averages do not capture.
Budget around $5,250 for the typical project (a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground) in North Carolina, with most jobs landing between $2,550 and $10,900. That typical figure is 3% below the national typical of $5,400, because North Carolina labor runs at 0.94× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within North Carolina, the typical project runs from about $5,050 in Greensboro to about $5,450 in Raleigh, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.