(01) — Cost guide · Georgia edition
Patio Cost in Georgia (2026)
In Georgia, patio cost for the typical project costs about $5,200 — 4% below the national average of $5,400. The gap comes from labor: Georgia labor runs at 0.92× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Georgia numbers, city prices and code notes.
- $2,500
- low end in Georgia — simple spec
- $5,200
- typical in Georgia — most homeowners pay near this
- $10,800
- high end in Georgia — premium materials, complex site
- $16.39
- per sq ft installed, typical concrete-paver patio, Georgia-adjusted
Typical project used for these figures: a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground. Ranges are 2026 planning figures for a professional installation in Georgia, derived from the national guide as explained below — always confirm with local quotes.
Georgia prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Georgia labor sits at 0.92× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Georgia range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Georgia | Difference |
|---|---|---|---|
| Low end | $2,600 | $2,500 | 4% below |
| Typical project | $5,400 | $5,200 | 4% below |
| High end | $11,200 | $10,800 | 4% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national patio cost guide. The table below re-prices that same breakdown for Georgia.
Cost breakdown, Georgia-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Georgia index of 0.92. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Georgia) | Total |
|---|---|---|---|
| Excavation & gradingDigging 7–9 in deep, grading for drainage fall away from the house, hauling spoil | $50 | $400 | $450 |
| Gravel base & beddingAbout 4–6 in of compacted crushed stone plus a 1 in screeded bedding-sand layer | $650 | $350 | $1,000 |
| Pavers320 sq ft of standard concrete pavers including the waste allowance for cuts | $1,750 | $0 | $1,750 |
| Laying & jointing laborSetting the field and border, cutting edges, compacting and sweeping joints | $0 | $1,050 | $1,050 |
| Edge restraints & cutsSpiked edge restraint on all open sides; diamond-blade cuts at borders and obstacles | $250 | $250 | $500 |
| Joint sand, sealer & cleanupPolymeric joint sand, optional sealer coat, wash-down and site cleanup | $200 | $150 | $350 |
| Delivery & permitsMaterial delivery and permit where the jurisdiction requires one | $50 | $0 | $50 |
| Total for the typical projectState-adjusted from the national breakdown above | $2,950 | $2,250 | $5,200 |
Typical cost by city in Georgia
Labor markets differ within a state too. These city figures apply each city's multiplier to the Georgia typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Columbus | $4,800 |
| Macon | $4,800 |
| Augusta | $4,900 |
| Athens | $5,000 |
| Savannah | $5,100 |
| Atlanta | $5,400 |
Georgia rules, climate and code that change the price
Georgia's climate driver is humidity, heat and summer storms rather than frost — frost depth is only about 12 in in the north and negligible in the south, so footings are shallow and cheap. The state residential code applies statewide with local amendments, and Atlanta-area jurisdictions are the strictest on permits and inspections. Termite protection is a real line item here: soil treatment and borate-treated framing are standard practice, and coastal wind requirements apply around Savannah.
Patio Cost in Georgia: what to watch
Georgia patio building is a humidity and clay job, and the cheapest in Wave 2. A typical 16 × 20 ft paver patio runs about $5,200 — under the national typical of $5,400 — with Atlanta about $5,400 and Macon about $4,800. Frost is barely a factor — frost depth is only about 12 in in the north and negligible in the south — so the base can be shallower than in northern states, but Georgia red clay still heaves and settles when it gets wet and dries, which is why compaction matters even here. Humidity grows algae on shaded pavers, so a sealer coat pays back, and summer thunderstorms test the drainage fall: a patio that ponds after a storm needs regrading, not more sand. Atlanta-area jurisdictions enforce permits and inspections most thoroughly.
What to ask contractors in Georgia
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Georgia counties and cities require permits for roofing, decks and structural work under the state residential code, with Atlanta-area jurisdictions the most thorough. Termite protection measures are typically inspected as part of framing work.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Georgia labor market: a quote far above the $5,200 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Georgia
Georgia counties and cities require permits for roofing, decks and structural work under the state residential code, with Atlanta-area jurisdictions the most thorough. Termite protection measures are typically inspected as part of framing work.
Georgia labor runs about 8% below the national average, with Atlanta roughly 4% above the state figure. Shallow footings keep groundwork cheap; the local extras are termite protection and, near the coast, wind-rated connections.
Budget around $5,200 for the typical project (a 16 × 20 ft (320 sq ft) concrete-paver patio on a compacted gravel base, new build on level ground) in Georgia, with most jobs landing between $2,500 and $10,800. That typical figure is 4% below the national typical of $5,400, because Georgia labor runs at 0.92× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Georgia, the typical project runs from about $4,800 in Columbus to about $5,400 in Atlanta, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.