(01) — Cost guide · Florida edition

Garage Door Replacement Cost in Florida (2026)

In Florida, garage door replacement cost for the typical project costs about $1,900 — 1% above the national average of $1,900. The gap comes from labor: Florida labor runs at 1.02× the national average, and labor is about 30% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Florida numbers, city prices and code notes.

$1,200
low end in Florida — simple spec
$1,900
typical in Florida — most homeowners pay near this
$5,050
high end in Florida — premium materials, complex site
$1,911.40
installed for a double insulated steel garage door (16 × 7 ft, R-12), Florida-adjusted

Typical project used for these figures: replacing a double (16 ft × 7 ft) insulated steel garage door (R-12), installed, including removal and disposal of the old door. Ranges are 2026 planning figures for a professional installation in Florida, derived from the national guide as explained below — always confirm with local quotes.

Florida prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Florida labor sits at 1.02× the national average. Applying that index to the labor share (about 30% of the installed price) gives the Florida range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageFloridaDifference
Low end$1,200$1,2001% above
Typical project$1,900$1,9001% above
High end$5,000$5,0501% above

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national garage door replacement cost guide. The table below re-prices that same breakdown for Florida.

Cost breakdown, Florida-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the Florida index of 1.02. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (Florida)Total
Insulated steel double door — 16 × 7 ft, R-12, triple-layerSteel panels with polystyrene insulation and an interior steel skin, 24-gauge, with windows and decorative hardware where specified $1,100 $0 $1,100
Installation labor — hang, level and balanceSet the door in the opening, level and plumb the tracks, and balance the door on its springs so it holds halfway by hand $0 $350 $350
Springs, tracks and hardwareTorsion springs sized to the door weight, new tracks, rollers, hinges and cables — never reuse springs from the old door $150 $50 $200
Weatherstripping and sealsBottom rubber seal, side weatherstripping and top seal, compressed firmly against the floor when the door closes $50 $50 $100
Removal and disposal of old doorTake down the old door and springs, haul them away, and dispose of them under local rules $0 $100 $100
Delivery and permitMaterial delivery and the building permit where the town requires one for a door replacement ($50 to $150) $50 $0 $50
Total for the typical projectState-adjusted from the national breakdown above $1,350 $550 $1,900

Typical cost by city in Florida

Labor markets differ within a state too. These city figures apply each city's multiplier to the Florida typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Tallahassee$1,750
Orlando$1,850
Jacksonville$1,850
Tampa$1,900
Miami$2,050
Fort Lauderdale$2,050

Florida rules, climate and code that change the price

Florida's cost driver is wind, not frost: the Florida Building Code sets high-velocity hurricane zone requirements in Miami-Dade and Broward counties and wind-speed maps statewide, so roofing needs enhanced nailing patterns and rated products, and fences and decks need wind-rated posts and connections. There is effectively no frost depth, so footings are shallow, but the water table and sandy soils affect post setting. Permits are required for roofing, decks and most structural work, and re-roofing triggers a code-compliance inspection of the decking underneath.

Garage Door Replacement Cost in Florida: what to watch

How much does a garage door replacement cost in Florida? A double (16 × 7 ft) insulated steel door (R-12), installed, runs about $1,900 — at the national typical, with most Florida jobs landing between $1,200 and $5,050. Miami runs about $2,050, while Tallahassee runs about $1,750. Florida garage doors are a wind job first: the Florida Building Code sets high-velocity hurricane zone requirements in Miami-Dade and Broward counties, and wind-load rated doors (typically rated to 130 to 150 mph) cost $200 to $500 more than a standard door but are required by code and by most insurers. Salt air corrodes uncoated steel hardware, so aluminum, fiberglass or vinyl doors — or stainless hardware on a steel door — are worth the premium near the coast. Humidity also punishes a wood door that is not refinished every 2 to 3 years. A Florida quote must name the wind rating and the hardware material, not just the door size, because a door that cannot hold in a storm is not a bargain at any price.

What to ask contractors in Florida

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: Florida requires permits for roof replacements, decks and most structural projects in every county, and a re-roof inspection checks the condition of the roof deck itself. In Miami-Dade and Broward, products must carry high-velocity hurricane zone approval, which narrows material choice and raises prices.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the Florida labor market: a quote far above the $1,900 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — Florida

How to read these numbers. Last updated October 2026 · Florida figures are derived from the national guide by scaling the labor share (about 30% of the installed price) by the Florida labor index of 1.02; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.