(01) — Cost guide · National edition
Countertop Installation Cost in 2026
A countertop quote is really three prices stacked together: the slab, the fabrication that cuts and edges it, and the installation that sets it level on your cabinets. Here is what countertop installation actually costs in 2026 — by material, line by line, and set against the cost of doing it yourself.
- $2,000
- low end — simple spec, DIY-friendly scope
- $2,700
- typical — most homeowners pay near this
- $4,500
- high end — premium materials, complex site
- $90
- per sq ft installed for standard quartz, including fabrication and one sink cutout
Typical project used for these figures: a 30 sq ft kitchen countertop in quartz, standard 25 in deep run with one sink cutout. Ranges are 2026 US national averages for a professional installation unless stated.
What it costs, and why the range is wide
Most homeowners replacing a kitchen countertop in 2026 pay between $2,000 and $4,500, with a typical 30 sq ft kitchen in quartz landing near $2,700 installed. The spread is not arbitrary: installed prices run roughly $20 to $150 per sq ft depending on material, and the slab itself is often the smaller share — templating, fabrication and installation run 40 to 50 percent of the total, and they rise with edge profiles, sink cutouts, seams and removal of the old top. A small galley kitchen in laminate costs a fraction of a large island in marble, for the same reason in both cases: the material sets the floor, and the fabrication sets the ceiling.
The material decision drives everything else. Quartz is the default choice in 2026 because it needs no sealing, resists stains and comes in consistent colors — but it cannot go outdoors, because UV yellows the resin, and it is heavier than laminate, so the cabinets underneath must be sound and level. Granite is the natural-stone alternative: each slab is unique, it takes heat better than quartz, but it needs sealing every 1 to 2 years and can vary in color from the sample. Laminate is the budget answer at a fifth of the price of stone, and modern laminates mimic stone convincingly, but they scorch, scratch and cannot be repaired once damaged. Work out your own area first with the Countertop Calculator, and price the slab itself with the Countertop Slab Calculator before you start getting quotes.
Waste and seams are real line items, not rounding errors: buy 10 percent extra on the slab area for cutting and breakage, and know that a run longer than a single slab (typically 120 in by 60 in for quartz) needs a seam — a well-made seam is nearly invisible on a busy pattern and more visible on a plain one, so choose the pattern with the seam in mind. Stone is sold by the slab, not the square foot, so a small kitchen may still pay for most of a slab: ask whether the fabricator has a remnant that fits your run, because a remnant can cut the material cost by a third.
Cost breakdown: where the money goes
For the typical 30 sq ft kitchen countertop in quartz, standard 25 in deep run with one sink cutout, the job usually builds up like this:
| Line item | Materials | Labor | Total |
|---|---|---|---|
| Quartz slabs, 33 sq ft with wasteQuartz at about $36 per sq ft, including a 10% cutting and breakage allowance | $1,200 | $0 | $1,200 |
| Fabrication — edge profile, sink cutout, polishingCNC cutting, eased edge profile, undermount sink cutout and polished finish | $100 | $500 | $600 |
| Installation and settingDelivery, dry-fit, levelling on the cabinets, seaming and sealing the joints | $50 | $400 | $450 |
| Templating and measurementDigital or physical template taken after the cabinets are set and level | $0 | $150 | $150 |
| Removal and disposal of old countertopLift and haul away the old top and backsplash, and clean the cabinet tops | $0 | $300 | $300 |
| Total for a typical kitchen countertop30 sq ft in quartz, one sink cutout — about $90 per sq ft installed | $1,350 | $1,350 | $2,700 |
Materials and labor are split the way contractors build a quote, so you can compare a real bid line by line. Figures are for the typical project above and will move with your spec — the next sections explain what moves them.
Cost by countertop material
Material moves the price more than kitchen size does — a laminate top costs a fifth of a marble one for the same run, because the slab and the fabrication are both cheaper. Prices below are installed, per sq ft.
| Material | Installed per sq ft | Typical 30 sq ft | Best for |
|---|---|---|---|
| Laminate | $20 – $50 | $600 – $1,500 | Budget kitchens and rentals — cheap, light, wide choice, but scorches and scratches and cannot be repaired |
| Butcher block (wood) | $40 – $70 | $1,200 – $2,100 | Warm, repairable worktops — needs oiling every few months and hates standing water at the sink |
| Solid surface (Corian and similar) | $50 – $80 | $1,500 – $2,400 | Seamless looks with integrated sinks — scratches can be sanded out, but it scorches under hot pans |
| Granite | $50 – $100 | $1,500 – $3,000 | Natural stone with heat resistance — each slab is unique, needs sealing every 1 to 2 years |
| Quartz (engineered stone) | $60 – $110 | $1,800 – $3,300 | Most kitchens — no sealing, stain-resistant, consistent color, but not for outdoor use |
| Marble | $75 – $150 | $2,250 – $4,500 | High-end kitchens and baking stations — beautiful, but etches with acids and stains without sealing |
Count your own area and slab needs with the Countertop Calculator — and when the room itself needs measuring, the Square Footage Calculator gives the area the slab count starts from.
What a standard quote includes — and what it leaves out
Usually included
- Slab material to the agreed quantity, including the 10% cutting and breakage allowance
- Templating after the cabinets are set and level, and fabrication — cutting, edge profiling and polishing
- One sink cutout (usually undermount) and faucet holes as specified in the quote
- Delivery, dry-fitting, levelling on the cabinets, seaming and sealing the joints
- Sealing of natural stone where specified, and cleanup of the work area
- Removal of the old countertop and backsplash, where the quote includes it
Commonly billed as extras
- The sink and faucet themselves — the countertop quote covers the cutout, not the fixtures that mount in it
- Cabinet repair or levelling — cabinets that are out of level must be fixed before templating, priced separately
- Plumbing and electrical moves — relocating a sink, dishwasher or cooktop is a plumber or electrician's job
- Backsplash tile beyond the standard 4 in stone upstand — a full-height tile backsplash is a separate job
- Additional cutouts beyond the first — each extra sink, cooktop or outlet cutout typically adds $100 to $250
- Matching discontinued stone — if the slab is out of production, sourcing a match is a separate cost and often impossible
DIY or hire a pro?
Countertop replacement is a poor DIY candidate for stone and a reasonable one for laminate and butcher block, because the difference is the fabrication: cutting a quartz or granite slab needs a CNC bridge saw, water cooling and a dust-controlled shop, and a slab that cracks in handling is a $1,000 mistake. A laminate top, by contrast, can be cut with a circular saw and a router, and a butcher-block top can be cut, sanded and oiled in a home workshop — a 30 sq ft laminate job runs $600 to $1,500 professionally installed against roughly $300 to $600 in materials for a careful DIYer.
What the professional actually sells is the template and the fit. Cabinets are never perfectly level or square, and a stone top that is templated wrong, cut wrong or set on an unlevel cabinet cracks, rocks or shows a gap at the wall that no caulk hides. The sensible split is to DIY a laminate or butcher-block top (straight runs, no complex cutouts, sound cabinets) and hire out quartz, granite, marble and solid surface — and any job with an undermount sink, a waterfall edge, a seam in a visible spot, or cabinets that are not level. If you DIY, measure three times, cut the sink opening with a template and a router rather than freehand, and support every overhang over 10 in with brackets.
Honest difficulty rating: High for stone and quartz — templating and cutting need shop equipment; moderate for laminate and butcher block on straight runs.
What drives the cost up or down
- Material choice. Laminate is $20–$50 per sq ft installed; marble is $75–$150. The slab sets the floor of the quote, and the fabrication cost follows it — stone needs shop cutting, laminate does not.
- Edge profile. A standard eased edge is usually included. Ogee, bullnose, waterfall and mitred edges add $10 to $40 per linear ft, and a waterfall edge on an island can add $800 to $1,500 on its own.
- Cutouts and fixtures. One sink cutout is usually included; each additional cutout — a second sink, a cooktop, a pop-up outlet — typically adds $100 to $250, and an undermount sink needs a polished cutout and support brackets.
- Slab size and seams. A run longer than a single slab (about 120 in by 60 in for quartz) needs a seam, and L-shaped kitchens need two. Seams add fabrication time and are more visible on plain patterns than on busy ones.
- Cabinet condition. Stone needs level, sound cabinets — a cabinet that is out of level by more than 1/8 in over 10 ft must be shimmed or repaired before templating, and that work is found only once the old top is off.
- Removal and access. Removing a glued-down laminate or tile top takes longer than lifting a stone top, and tight stairwells, small elevators and long carries add handling time for heavy slabs — a quartz slab weighs about 20 lb per sq ft.
How to keep the cost down
- Ask whether the fabricator has a remnant that fits your run — a remnant can cut the material cost by a third on a small kitchen.
- Choose the pattern with the seam in mind: a busy granite or quartz pattern hides a seam, a plain white one shows it.
- Get the template done only after the cabinets are set, level and finished — templating early is how tops arrive the wrong size.
- Confirm what is included by name: templating, fabrication, edge profile, sink cutout, delivery, setting and sealing.
- For granite and marble, ask when sealing is included and how often to reseal — unsealed stone stains, and sealing is not a one-time job.
- Compare quotes on the same specification: material and grade, edge profile, cutouts, seam positions and removal, each named.
Frequently asked questions
Quartz countertops typically run $60 to $110 per sq ft installed, including fabrication and one sink cutout — a 30 sq ft kitchen is about $2,700 at the typical $90 per sq ft. The slab itself is roughly $36 per sq ft, and templating, cutting, edge profiling and installation make up the rest. Busy patterns cost the same as plain ones, but plain patterns show seams more, so the slab layout matters.
They are close: granite runs $50 to $100 per sq ft installed and quartz $60 to $110, so a 30 sq ft kitchen is about $1,500 to $3,000 in granite and $1,800 to $3,300 in quartz. The difference is maintenance, not price — granite needs sealing every 1 to 2 years and can vary from the sample, while quartz needs no sealing and is color-consistent, but it cannot go outdoors because UV yellows the resin.
A small kitchen of about 30 sq ft costs $600 to $1,500 in laminate, $1,200 to $2,100 in butcher block, $1,500 to $3,000 in granite and $1,800 to $3,300 in quartz, installed. Small kitchens pay a premium per sq ft because templating, fabrication setup and delivery are largely fixed costs, and a small run may still pay for most of a slab — ask about remnants, which can cut the material cost by a third.
Usually one sink cutout is included in the installed price, cut and polished for an undermount sink. Each additional cutout — a second sink, a cooktop, a pop-up outlet — typically adds $100 to $250. The sink and faucet themselves are not included: the countertop quote covers the hole, not the fixtures that mount in it.
From template to installed top is usually 1 to 2 weeks: templating takes an hour once the cabinets are set and level, fabrication takes 5 to 10 working days, and installation itself is a single day for a standard kitchen. The old top is removed the same day the new one is set, so the kitchen is without a countertop for hours, not days — but do not schedule the plumber to reconnect the sink until the top has set for 24 hours.
Cost by state
Labor is the part of the price that moves most by location. These state editions re-price this guide with the local labor index, add city prices and the state-specific permit and code notes.
Countertop Installation Cost in Texas
State-adjusted prices, city figures and Texas code notes.
Read the guideCountertop Installation Cost in California
State-adjusted prices, city figures and California code notes.
Read the guideCountertop Installation Cost in Florida
State-adjusted prices, city figures and Florida code notes.
Read the guideCountertop Installation Cost in New York
State-adjusted prices, city figures and New York code notes.
Read the guideCountertop Installation Cost in Pennsylvania
State-adjusted prices, city figures and Pennsylvania code notes.
Read the guideCountertop Installation Cost in Illinois
State-adjusted prices, city figures and Illinois code notes.
Read the guideCountertop Installation Cost in Ohio
State-adjusted prices, city figures and Ohio code notes.
Read the guideCountertop Installation Cost in Georgia
State-adjusted prices, city figures and Georgia code notes.
Read the guideCountertop Installation Cost in North Carolina
State-adjusted prices, city figures and North Carolina code notes.
Read the guideCountertop Installation Cost in Michigan
State-adjusted prices, city figures and Michigan code notes.
Read the guideMore cost guides
Deck Build Cost
Materials and labor for a ground-level deck in pressure-treated lumber, cedar and composite, priced per square foot with railing and stair allowances.
Read the guideRoof Replacement Cost
Tear-off and replacement per roofing square for architectural shingles, metal and tile, including underlayment, flashing and disposal.
Read the guideBathroom Remodel Cost
Full and partial remodels at three finish levels, split between fixtures, tile, plumbing, electrical and labor.
Read the guide