(01) — Cost guide · Texas edition
Concrete Driveway Cost in Texas (2026)
In Texas, concrete driveway cost for the typical project costs about $5,250 — 3% below the national average of $5,400. The gap comes from labour: Texas labour runs at 0.94× the national average, and labour is about 45% of an installed price, so the state figure below scales the labour share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Texas numbers, city prices and code notes.
- $2,900
- low end in Texas — simple spec
- $5,250
- typical in Texas — most homeowners pay near this
- $10,700
- high end in Texas — premium materials, complex site
- $8.76
- per sq ft installed, typical plain broom-finish driveway, Texas-adjusted
Typical project used for these figures: a 24 × 25 ft (600 sq ft) two-car driveway, 4 in thick, broom finish, new build on prepared ground. Ranges are 2026 planning figures for a professional installation in Texas, derived from the national guide as explained below — always confirm with local quotes.
Texas prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labour is what moves, and Texas labour sits at 0.94× the national average. Applying that index to the labour share (about 45% of the installed price) gives the Texas range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labour market, and it is worth asking which line moved.
| Figure | National average | Texas | Difference |
|---|---|---|---|
| Low end | $3,000 | $2,900 | 3% below |
| Typical project | $5,400 | $5,250 | 3% below |
| High end | $11,000 | $10,700 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national concrete driveway cost guide. The table below re-prices that same breakdown for Texas.
Cost breakdown, Texas-adjusted
The national guide's line items, with materials held at national prices and labour scaled by the Texas index of 0.94. Compare a real bid against this table line by line: if a contractor's labour lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labour (Texas) | Total |
|---|---|---|---|
| Excavation & gradingDigging to depth, grading for drainage fall, hauling spoil | $100 | $650 | $750 |
| Gravel baseAbout 4 in of compacted crushed stone — the foundation of the slab | $450 | $350 | $800 |
| Reinforcement & formsWelded mesh or rebar on chairs, timber forms set to level and line | $400 | $300 | $700 |
| ConcreteAbout 8 cu yd delivered including waste allowance, standard 4,000 psi mix | $1,250 | $0 | $1,250 |
| Placing & finishing labourPouring, screeding, floating and broom finishing | $0 | $1,200 | $1,200 |
| Joints, curing & sealingControl joints cut or tooled, curing, penetrating sealer | $150 | $150 | $300 |
| Permits & cleanupPermit where required, washout and site cleanup | $100 | $200 | $300 |
| Total for the typical projectState-adjusted from the national breakdown above | $2,450 | $2,750 | $5,200 |
Typical cost by city in Texas
Labour markets differ within a state too. These city figures apply each city's multiplier to the Texas typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| El Paso | $4,750 |
| San Antonio | $5,050 |
| Fort Worth | $5,150 |
| Houston | $5,250 |
| Dallas | $5,350 |
| Austin | $5,650 |
Texas rules, climate and code that change the price
Texas has no statewide general-contractor licence, so permit rules and inspection quality vary by city — Houston, Dallas and Austin all run their own permitting portals with different thresholds, and unincorporated areas may require no building permit at all. Frost depth is shallow across most of the state (often 6–12 in), which keeps footing work cheap, but expansive clay soils around Dallas–Fort Worth and Houston move with moisture and demand deeper, belled piers for decks and fences. Gulf Coast wind and hail exposure raises roofing and fence specifications, and hail-resistant shingles are a common insurance-driven upgrade.
Concrete Driveway Cost in Texas: what to watch
Texas concrete driveways are an expansive-clay job. The clay soils across much of the state swell when wet and shrink when dry, which cracks thin, unreinforced slabs, so a Texas driveway needs a thicker slab, proper reinforcement, control joints at the right spacing and a compacted, stable base — the specification matters more than the concrete price. Summer heat changes the pour itself: concrete placed in a Texas afternoon needs curing protection or it loses strength at the surface, so schedule morning pours and confirm the curing plan in writing. Drainage must carry storm water away from the slab foundation, because water pooling at the slab edge feeds the same soil movement that cracks the driveway.
What to ask contractors in Texas
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Most Texas cities require a permit for a roof replacement, a deck over 30 in high or attached to the house, and any structural work, but thresholds differ by city and unincorporated land often has none. Check the city permitting portal before work starts — an unpermitted deck or roof can stall a future sale even where enforcement is light.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labour basis: Ask how the quote treats the Texas labour market: a quote far above the $5,250 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Texas
Most Texas cities require a permit for a roof replacement, a deck over 30 in high or attached to the house, and any structural work, but thresholds differ by city and unincorporated land often has none. Check the city permitting portal before work starts — an unpermitted deck or roof can stall a future sale even where enforcement is light.
Texas labour runs about 6% below the national average, so installed prices sit slightly under national figures, but Austin runs roughly 8% above the state figure and Gulf Coast wind/hail specifications can erase the saving on roofing. Material prices are national; it is the labour line and the local code extras that move a Texas quote.
Budget around $5,250 for the typical project (a 24 × 25 ft (600 sq ft) two-car driveway, 4 in thick, broom finish, new build on prepared ground) in Texas, with most jobs landing between $2,900 and $10,700. That typical figure is 3% below the national typical of $5,400, because Texas labour runs at 0.94× the national average and labour is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Texas, the typical project runs from about $4,750 in El Paso to about $5,650 in Austin, reflecting local labour markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.