(01) — Cost guide · South Carolina edition

Solar Panel Installation Cost in South Carolina (2026)

In South Carolina, solar panel installation cost for the typical project costs about $16,600 — 3% below the national average of $17,100. The gap comes from labor: South Carolina labor runs at 0.9× the national average, and labor is about 30% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the South Carolina numbers, city prices and code notes.

$11,050
low end in South Carolina — simple spec
$16,600
typical in South Carolina — most homeowners pay near this
$27,650
high end in South Carolina — premium materials, complex site
$2.76
per watt installed, gross — the 6 kW typical system nets to $11,970 after the 30% federal credit, South Carolina-adjusted

Typical project used for these figures: a 6 kW rooftop system — 15 × 400 W panels, string inverter, no battery — on a straightforward single-story roof. Ranges are 2026 planning figures for a professional installation in South Carolina, derived from the national guide as explained below — always confirm with local quotes.

South Carolina prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and South Carolina labor sits at 0.9× the national average. Applying that index to the labor share (about 30% of the installed price) gives the South Carolina range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageSouth CarolinaDifference
Low end$11,400$11,0503% below
Typical project$17,100$16,6003% below
High end$28,500$27,6503% below

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national solar panel installation cost guide. The table below re-prices that same breakdown for South Carolina.

Cost breakdown, South Carolina-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the South Carolina index of 0.9. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (South Carolina)Total
Solar panels15 × 400 W modules (6 kW DC), tier-one residential panels $5,100 $550 $5,650
InverterString inverter sized to the array (microinverters price higher) $1,800 $250 $2,050
Racking, mounting & wiringRails, roof mounts and flashings, DC/AC cabling, combiner and disconnects $1,500 $800 $2,300
Installation laborRoof crew for the array plus the licensed electrician's tie-in work $300 $3,500 $3,800
Electrical panel work & monitoringBreaker and panel capacity work where needed, monitoring setup and app configuration $900 $550 $1,450
Permits, inspection & interconnectionBuilding/electrical permits, utility interconnection application and inspection fees $900 $250 $1,150
Total for the typical projectState-adjusted from the national breakdown above $10,500 $5,950 $16,450

Typical cost by city in South Carolina

Labor markets differ within a state too. These city figures apply each city's multiplier to the South Carolina typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Columbia$15,900
Greenville$16,250
North Charleston$16,600
Myrtle Beach$16,600
Charleston$17,250

South Carolina rules, climate and code that change the price

South Carolina is a low-cost labor market where hurricane wind rules govern the coast: the building code sets wind-speed and uplift requirements for roofing, decks and fences in coastal counties, and flood-zone rules affect ground-level structures. Frost depth is negligible in the Lowcountry and about 12 in upstate. Termite protection is standard statewide, and Charleston's historic-district rules can restrict roofing and fence materials in designated areas.

Solar Panel Installation Cost in South Carolina: what to watch

How much does solar cost in South Carolina? About $16,600 for a typical 6 kW rooftop system before incentives — about 3% below the national typical of $17,100 — with most South Carolina jobs landing between $11,050 and $27,650. Within the state, Charleston runs about $17,250, while Columbia runs about $15,950. South Carolina offers one of the strongest state incentives in the country: a 25% state tax credit up to $3,500 a year, which together with the federal credit cuts the net price substantially — verify which incentives the quote has already netted out. Net metering is available through Duke Energy and Dominion Energy, though terms vary by utility, and coastal installations need wind-rated racking. Heat and humidity trim production, so a reputable quote models Charleston summer output, not a brochure figure.

What to ask contractors in South Carolina

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: South Carolina requires permits for roofing, decks and structural work under the statewide residential code. Coastal counties add wind-uplift and flood-zone checks, and Charleston historic districts add material restrictions.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the South Carolina labor market: a quote far above the $16,600 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — South Carolina

How to read these numbers. Last updated October 2026 · South Carolina figures are derived from the national guide by scaling the labor share (about 30% of the installed price) by the South Carolina labor index of 0.9; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.