(01) — Cost guide · South Carolina edition

Roof Replacement Cost in South Carolina (2026)

In South Carolina, roof replacement cost for the typical project costs about $10,700 — 4% below the national average of $11,200. The gap comes from labor: South Carolina labor runs at 0.9× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the South Carolina numbers, city prices and code notes.

$5,750
low end in South Carolina — simple spec
$10,700
typical in South Carolina — most homeowners pay near this
$22,900
high end in South Carolina — premium materials, complex site
$6.30
per sq ft of roof area installed, typical architectural shingle job, South Carolina-adjusted

Typical project used for these figures: a 1,700 sq ft roof (about 17 squares) in architectural asphalt shingles, one old layer torn off. Ranges are 2026 planning figures for a professional installation in South Carolina, derived from the national guide as explained below — always confirm with local quotes.

South Carolina prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and South Carolina labor sits at 0.9× the national average. Applying that index to the labor share (about 45% of the installed price) gives the South Carolina range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageSouth CarolinaDifference
Low end$6,000$5,7504% below
Typical project$11,200$10,7004% below
High end$24,000$22,9004% below

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national roof replacement cost guide. The table below re-prices that same breakdown for South Carolina.

Cost breakdown, South Carolina-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the South Carolina index of 0.9. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (South Carolina)Total
Tear-off & disposalOne existing layer stripped, hauled and dumped $150 $1,250 $1,400
Decking repair allowanceReplacing a handful of damaged sheets; priced per sheet in most contracts $300 $250 $550
Underlayment & ice-and-water shieldSynthetic underlayment over the field, membrane at eaves and valleys $550 $400 $950
Architectural shinglesAbout 17 squares including waste and starter courses $3,300 $2,350 $5,650
Flashing, vents & ridge capStep and chimney flashing, vent boots, ridge ventilation and cap $450 $500 $950
Drip edge, starter strip & fastenersMetal drip edge at eaves and rakes, nails and sealants $300 $200 $500
Permits, inspection & cleanupPermit where required, magnetic nail sweep, site cleanup $350 $250 $600
Total for the typical projectState-adjusted from the national breakdown above $5,400 $5,200 $10,600

Typical cost by city in South Carolina

Labor markets differ within a state too. These city figures apply each city's multiplier to the South Carolina typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Columbia$10,250
Greenville$10,500
North Charleston$10,700
Myrtle Beach$10,700
Charleston$11,100

South Carolina rules, climate and code that change the price

South Carolina is a low-cost labor market where hurricane wind rules govern the coast: the building code sets wind-speed and uplift requirements for roofing, decks and fences in coastal counties, and flood-zone rules affect ground-level structures. Frost depth is negligible in the Lowcountry and about 12 in upstate. Termite protection is standard statewide, and Charleston's historic-district rules can restrict roofing and fence materials in designated areas.

Roof Replacement Cost in South Carolina: what to watch

A typical 1,700 sq ft architectural shingle roof replacement in South Carolina runs about $10,700, with most jobs landing between $5,750 and $22,900. Charleston runs a little above the typical at about $11,100, while Columbia runs about $10,250 and Greenville about $10,500. South Carolina roofing splits by geography: hurricane wind and uplift requirements govern the coast, where wind-rated shingles, sealed decks and uplift-resistant connections are required, while the Upstate faces only a light frost depth of about 12 in and no wind-rating premium; termite protection is standard statewide, and Charleston's historic-district rules can restrict roofing materials in designated areas. Permits run through the statewide residential code, with coastal counties adding wind-uplift and flood-zone checks. If your home is in a coastal county, confirm the wind rating and sealed-deck detail are in the quote, and in Charleston check the historic-district material rules before choosing a shingle.

What to ask contractors in South Carolina

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: South Carolina requires permits for roofing, decks and structural work under the statewide residential code. Coastal counties add wind-uplift and flood-zone checks, and Charleston historic districts add material restrictions.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the South Carolina labor market: a quote far above the $10,700 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — South Carolina

How to read these numbers. Last updated October 2026 · South Carolina figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the South Carolina labor index of 0.9; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.