(01) — Cost guide · North Carolina edition
Kitchen Remodel Cost in North Carolina (2026)
In North Carolina, kitchen remodel cost for the typical project costs about $26,750 — 3% below the national average of $27,500. The gap comes from labour: North Carolina labour runs at 0.94× the national average, and labour is about 45% of an installed price, so the state figure below scales the labour share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the North Carolina numbers, city prices and code notes.
- $7,800
- low end in North Carolina — simple spec
- $26,750
- typical in North Carolina — most homeowners pay near this
- $77,850
- high end in North Carolina — premium materials, complex site
- $223.79
- per sq ft of floor area, typical minor mid-range remodel, North Carolina-adjusted
Typical project used for these figures: a minor mid-range remodel of a 10 × 12 ft kitchen — new semi-custom cabinets in the same layout, quartz counters, mid-range appliances. Ranges are 2026 planning figures for a professional installation in North Carolina, derived from the national guide as explained below — always confirm with local quotes.
North Carolina prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labour is what moves, and North Carolina labour sits at 0.94× the national average. Applying that index to the labour share (about 45% of the installed price) gives the North Carolina range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labour market, and it is worth asking which line moved.
| Figure | National average | North Carolina | Difference |
|---|---|---|---|
| Low end | $8,000 | $7,800 | 3% below |
| Typical project | $27,500 | $26,750 | 3% below |
| High end | $80,000 | $77,850 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national kitchen remodel cost guide. The table below re-prices that same breakdown for North Carolina.
Cost breakdown, North Carolina-adjusted
The national guide's line items, with materials held at national prices and labour scaled by the North Carolina index of 0.94. Compare a real bid against this table line by line: if a contractor's labour lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labour (North Carolina) | Total |
|---|---|---|---|
| CabinetsSemi-custom, installed and levelled; about 35% of the whole budget | $8,000 | $1,600 | $9,600 |
| CountertopsQuartz, about 35 sq ft including the sink cutout and edge profile | $2,600 | $850 | $3,450 |
| AppliancesMid-range suite: range, refrigerator, dishwasher, microwave | $4,500 | $400 | $4,900 |
| FlooringLuxury vinyl or mid-range hardwood over the 120 sq ft floor | $900 | $750 | $1,650 |
| BacksplashSubway or similar tile, about 30 sq ft, set and grouted | $550 | $600 | $1,150 |
| Plumbing & electricalReconnect in place, code upgrades, under-cabinet lighting circuits | $800 | $1,600 | $2,400 |
| Sink, faucet & hardwareUndermount sink, pull-down faucet, cabinet pulls | $700 | $300 | $1,000 |
| LightingRecessed and under-cabinet fixtures, dimmers | $500 | $450 | $950 |
| Paint & finishingWalls and ceiling, trim touch-ups | $350 | $600 | $950 |
| Demolition, permits & disposalStrip-out of the old kitchen, permit where required, dump fees | $200 | $750 | $950 |
| Total for the typical projectState-adjusted from the national breakdown above | $19,100 | $7,900 | $27,000 |
Typical cost by city in North Carolina
Labour markets differ within a state too. These city figures apply each city's multiplier to the North Carolina typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Greensboro | $25,700 |
| Winston-Salem | $25,700 |
| Durham | $26,750 |
| Wilmington | $26,750 |
| Charlotte | $27,300 |
| Raleigh | $27,850 |
North Carolina rules, climate and code that change the price
North Carolina's code is statewide (the NC Residential Code) with local enforcement, and its geography splits costs: the mountains need deeper frost footings and snow consideration, the Piedmont is moderate, and the coast carries hurricane wind requirements. Frost depth is about 12–18 in in the Piedmont and deeper in the mountains. The Research Triangle and Charlotte are the state's higher-cost metros, while coastal wind detailing adds cost in the east even though labour there is average.
Kitchen Remodel Cost in North Carolina: what to watch
North Carolina kitchen remodels span three climates and two very different housing stocks. Coastal kitchens need moisture and salt-air detailing and flood-zone awareness on ground floors, mountain kitchens need freeze protection for pipes in exterior walls, and the fast-growing Charlotte and Raleigh suburbs are mostly newer homes with straightforward layouts. The NC Residential Code applies statewide with local enforcement, and the Research Triangle and Charlotte are the higher-cost metros. Older homes in the Piedmont often hide lead paint and outdated wiring, while new-build kitchens reward layout tweaks over structural work. Match the specification to your region, and confirm whether your HOA reviews exterior changes like vent terminations before ordering cabinets.
What to ask contractors in North Carolina
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: North Carolina requires permits for roofing, decks and structural work in every county under the state residential code. Coastal counties add wind-borne debris and uplift requirements that the permit review checks on roofing and deck connections.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labour basis: Ask how the quote treats the North Carolina labour market: a quote far above the $26,750 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — North Carolina
North Carolina requires permits for roofing, decks and structural work in every county under the state residential code. Coastal counties add wind-borne debris and uplift requirements that the permit review checks on roofing and deck connections.
North Carolina labour runs about 6% below the national average, with Raleigh and Charlotte slightly above the state figure. Mountain frost footings and coastal wind detailing are the two regional adders that national averages do not capture.
Budget around $26,750 for the typical project (a minor mid-range remodel of a 10 × 12 ft kitchen — new semi-custom cabinets in the same layout, quartz counters, mid-range appliances) in North Carolina, with most jobs landing between $7,800 and $77,850. That typical figure is 3% below the national typical of $27,500, because North Carolina labour runs at 0.94× the national average and labour is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within North Carolina, the typical project runs from about $25,700 in Greensboro to about $27,850 in Raleigh, reflecting local labour markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.