(01) — Cost guide · National edition
HVAC Replacement Cost in 2026
An HVAC replacement is really two purchases in one: the equipment (the condenser, coil and furnace) and the skilled labor that sizes it, installs it, charges the refrigerant and commissions it. Here is what HVAC replacement actually costs in 2026 — by system type, line by line, and set against the cost of doing it yourself (spoiler: do not).
- $7,000
- low end — simple spec, DIY-friendly scope
- $10,500
- typical — most homeowners pay near this
- $15,000
- high end — premium materials, complex site
- $10,500
- installed for a 3-ton central AC and gas furnace replacement
Typical project used for these figures: a 3-ton central air conditioner and gas furnace replacement, installed, including removal and disposal of the old system. Ranges are 2026 US national averages for a professional installation unless stated.
What it costs, and why the range is wide
Most homeowners replacing a central heating and cooling system in 2026 pay between $7,000 and $15,000, with a typical 3-ton central air conditioner and gas furnace replacement landing near $10,500 installed. The spread is not arbitrary: the equipment alone runs roughly $5,000 to $8,000 depending on brand and efficiency tier, and installation labor is about 35 to 40 percent of the total, rising with ductwork repairs, electrical upgrades and permit costs. A small single-stage system in a mild climate costs a fraction of a high-efficiency variable-speed system in a home that also needs ductwork — for the same reason in both cases: the equipment sets the floor, and the condition of the house sets the ceiling.
The sizing decision drives everything else. A 3-ton system suits roughly 1,500 to 1,800 sq ft in a typical US home, but the right size depends on insulation, window area, ceiling height and climate — a well-insulated 1,800 sq ft home in Ohio may need only 2.5 tons, while a leaky 1,500 sq ft home in Texas may need 3.5. Oversizing is the most common and most expensive mistake in HVAC: an oversized air conditioner cools the air quickly, shuts off, and never runs long enough to remove humidity, leaving the house cold and clammy. Work out your home's area first with the Square Footage Calculator, then insist on a written Manual J load calculation before you accept any quote — a contractor who sizes by square footage alone, or by the size of the old system, is guessing.
Efficiency ratings are the second decision that moves the price. A standard 14.3 SEER2 air conditioner with an 80% AFUE furnace is the budget baseline, while a 16–18 SEER2 system with a 96% AFUE condensing furnace adds $2,000 to $4,000 to the installed price and cuts heating and cooling bills by 20 to 30 percent. In hot climates the air conditioner's SEER2 rating does the heavy lifting; in cold climates the furnace AFUE and the heat pump's cold-weather performance matter more. Check the federal tax credits and your utility's rebate program before you sign — high-efficiency systems often qualify for credits worth hundreds of dollars, and the credit is claimed on the installed cost, not the equipment alone.
Cost breakdown: where the money goes
For the typical 3-ton central air conditioner and gas furnace replacement, installed, including removal and disposal of the old system, the job usually builds up like this:
| Line item | Materials | Labor | Total |
|---|---|---|---|
| Equipment — 3-ton AC condenser, evaporator coil, 80% AFUE gas furnaceSingle-stage 14.3 SEER2 condenser and matching coil with a 60,000 BTU gas furnace | $5,500 | $0 | $5,500 |
| Installation labor — set, connect, charge and commissionSet the equipment, braze and pressure-test the refrigerant lines, evacuate and charge the system, and run startup and safety tests | $0 | $2,300 | $2,300 |
| Ductwork modifications and sealingAdapt the supply plenum and return, seal accessible duct joints with mastic, and add or resize a return grille if airflow is short | $400 | $650 | $1,050 |
| Refrigerant lineset and condensate drainNew copper lineset sized to the condenser, insulated suction line, and a trapped condensate drain to a floor drain or pump | $250 | $350 | $600 |
| Electrical work — disconnect, wiring and breakerOutdoor disconnect switch, whip and wiring to the condenser, and a dedicated breaker sized to the new equipment | $200 | $250 | $450 |
| Permit and inspectionMechanical permit from the city or county and the final inspection of the installation | $250 | $0 | $250 |
| Removal and disposal of the old systemRecover the old refrigerant under EPA rules, haul away the condenser, coil and furnace, and reclaim or dispose of the refrigerant legally | $0 | $350 | $350 |
| Total for a typical HVAC replacement3-ton central AC and gas furnace, installed — about $10,500 | $6,600 | $3,900 | $10,500 |
Materials and labor are split the way contractors build a quote, so you can compare a real bid line by line. Figures are for the typical project above and will move with your spec — the next sections explain what moves them.
Cost by HVAC system type
System type moves the price more than house size does — a furnace-only replacement costs less than half of a full heat-pump system for the same home, because the equipment and the labor are both lighter. Prices below are installed, for a typical 3-ton equivalent in a home with existing ductwork.
| System type | Installed price | Typical | Best for |
|---|---|---|---|
| Furnace only (gas, 80–96% AFUE) | $4,500 – $8,000 | $5,500 | Homes with a working air conditioner and a failed furnace — the cheapest full replacement, and the right call when the AC still has years of life |
| Air conditioner only (condenser + coil) | $4,000 – $8,500 | $5,500 | Homes with a working furnace and a failed AC — pair it with a matching coil, because a mismatched coil kills efficiency and can void the warranty |
| Central AC + gas furnace | $7,000 – $15,000 | $10,500 | Most US homes with ductwork — the standard replacement, and the best value where winters are cold enough to need gas heat |
| Air-source heat pump | $8,000 – $16,000 | $11,500 | Mild to moderate climates and homes going all-electric — one system heats and cools, and cold-climate models now heat reliably well below freezing |
| Ductless mini-split (multi-zone) | $6,000 – $14,000 | $9,500 | Homes without ductwork, additions and zoned comfort — no ducts to lose energy through, but one indoor head per zone, so costs rise with room count |
Start from your home's area with the Square Footage Calculator — and if the house is drafty, check the Insulation Cost guide first, because sealing and insulating the attic can shrink the system you need by half a ton and pay for itself in equipment savings alone.
What a standard quote includes — and what it leaves out
Usually included
- Equipment to the agreed specification — condenser, evaporator coil and furnace, matched as a rated system
- Installation labor: setting the equipment, brazing and pressure-testing the refrigerant lines, evacuation, charging and startup testing
- A new refrigerant lineset and condensate drain, sized to the new equipment
- Ductwork adaptation at the equipment — plenum work, return adjustments and sealing of accessible joints
- Electrical work at the equipment — outdoor disconnect, wiring and a dedicated breaker
- The mechanical permit and the final inspection, where the quote includes them
- Removal of the old system, EPA-compliant refrigerant recovery, and haul-away and disposal
Commonly billed as extras
- Full duct replacement — if the ducts are undersized, leaking badly or lined with asbestos, replacing them is a separate job that can add $3,000 to $7,000
- A new thermostat beyond a basic model — a smart thermostat typically adds $150 to $300 installed
- Electrical panel upgrades — if the panel has no spare breaker capacity or is an older fuse panel, the electrician's work is priced separately
- Gas line work — a new or relocated gas line for the furnace, or a meter upgrade, is a plumber or gas utility job
- Structural or carpentry work — cutting new return openings, framing a closet for an air handler, or repairing a rotted furnace platform
- Asbestos or mold remediation — old duct insulation, furnace wrap or duct board may need licensed abatement before the crew can work
DIY or hire a pro?
HVAC replacement is not a DIY job, full stop. Installing a central air conditioner and furnace requires an EPA Section 608 certification to handle refrigerant, a mechanical permit and inspection in nearly every jurisdiction, and gas, electrical and brazing work where a mistake can kill — a gas leak, a carbon monoxide leak from a badly vented furnace, or an overcharged refrigerant circuit that destroys a $3,000 compressor on startup. The equipment itself is also effectively closed to homeowners: reputable manufacturers sell through licensed distributors and will not honor the warranty on a system installed by an unlicensed person, so a DIY install can void a 10-year parts warranty on day one.
What a homeowner can safely do is everything around the replacement: change the filter, clear leaves and debris from around the condenser, hose the condenser coil clean, seal accessible duct joints with mastic, and replace a thermostat. The sensible split is to DIY the maintenance and hire a licensed contractor for the replacement — and to vet that contractor properly: check the state license, ask for the Manual J load calculation in writing, confirm the permit is included, and get the equipment model numbers on the quote so you can verify the SEER2 and AFUE ratings yourself. If a quote is thousands below the others, it is usually missing the permit, the lineset, the ductwork or the commissioning — the four items a cheap install skips first.
Honest difficulty rating: Not a DIY job — refrigerant handling needs EPA Section 608 certification, gas and electrical work needs a license, and a DIY install voids the manufacturer warranty.
What drives the cost up or down
- System size (tonnage). Each additional ton adds roughly $1,000 to $2,000 installed, and the wrong size costs more than the right one: an oversized system short-cycles, fails to dehumidify and wears out early, while an undersized one runs constantly and never catches up on the hottest days. Size comes from a Manual J load calculation, not from the old system's nameplate.
- Efficiency tier (SEER2 and AFUE). A 14.3 SEER2 system with an 80% AFUE furnace is the budget baseline; a 16–18 SEER2 variable-speed system with a 96% AFUE condensing furnace adds $2,000 to $4,000 and cuts heating and cooling bills by 20 to 30 percent. The payback is fastest in hot climates and in homes with high heating bills.
- Ductwork condition. Leaky, undersized or damaged ducts are the hidden cost in most replacements: sealing and minor modifications run $500 to $1,500, while a full duct replacement adds $3,000 to $7,000. Ducts in a hot attic lose 25 to 30 percent of the conditioned air they carry, so a new system on bad ducts performs like an old one.
- Brand and warranty. Premium brands (Carrier, Trane, Lennox) run $1,000 to $2,500 more than budget brands for the same tonnage and efficiency, and the difference is mostly the dealer network and the warranty terms. A 10-year parts warranty is standard on a registered system — confirm registration is included, because unregistered equipment often carries only a 5-year warranty.
- Refrigerant transition (R-410A to R-454B). New equipment sold from 2025 uses low-global-warming-potential refrigerants such as R-454B instead of R-410A, under EPA rules phasing down high-GWP refrigerants. R-454B systems cost slightly more and need A2L-rated handling, and an R-410A system cannot be topped up with R-454B — the two refrigerants are not interchangeable.
- Access, permit and code upgrades. A furnace in a tight attic or crawl space costs more to replace than one in an open basement, and permit fees vary from under $100 in small towns to $500 or more in large cities. Code upgrades — a new condensate safety switch, a combustion-air vent, or an upgraded disconnect — are found only once the old system is out, so budget 10 percent for them.
How to keep the cost down
- Get the Manual J load calculation in writing before you compare quotes — three quotes for three different sizes are not comparable, and the right size is the cheapest system that actually works.
- Replace the air conditioner and furnace together when both are over 12 years old: a matched system is more efficient, carries a full warranty, and costs far less than two separate replacements a year apart.
- Compare quotes on the same specification: equipment model numbers, SEER2 and AFUE ratings, lineset, ductwork, permit and commissioning, each named.
- Ask whether the quote includes a new thermostat, a condensate safety switch and a surge protector — the three small items that prevent the three most common callbacks.
- Check federal tax credits and your utility rebate program before signing: high-efficiency systems often qualify for credits worth hundreds of dollars, claimed on the installed cost.
- Schedule the replacement in spring or fall, when HVAC contractors have open calendars — summer emergency replacements carry premium pricing and the shortest warranty on workmanship.
Frequently asked questions
A full HVAC replacement — a 3-ton central air conditioner and gas furnace, installed — typically costs $7,000 to $15,000, with $10,500 the typical price in 2026. The equipment is about $5,500 of that total and installation labor about $3,900, with ductwork, refrigerant lines, electrical work, the permit and disposal making up the rest. A furnace-only replacement runs $4,500 to $8,000, an AC-only replacement $4,000 to $8,500, and a heat pump $8,000 to $16,000.
A 3-ton central AC and gas furnace replacement costs about $10,500 installed, with a typical range of $7,000 to $15,000 depending on efficiency tier, brand and ductwork condition. A 3-ton system suits roughly 1,500 to 1,800 sq ft in a typical US home, but the right size depends on insulation, windows and climate — always get a Manual J load calculation rather than sizing from square footage alone. A 3-ton heat pump runs slightly more, about $11,500 typical.
Yes, when both are over 12 years old: a matched AC and furnace work together at their rated efficiency, carry a full 10-year parts warranty, and cost far less installed together than in two separate jobs a year apart. If one unit is under 8 years old and running well, replace only the failed one — but pair a new air conditioner with a matching evaporator coil, because a mismatched coil cuts efficiency and can void the warranty.
A standard AC and furnace replacement takes 1 to 2 days: the crew removes the old system, sets the new equipment, brazes and pressure-tests the refrigerant lines, evacuates and charges the system, and runs startup and safety tests. A job that also needs ductwork replacement, a new gas line or an electrical panel upgrade can run 3 to 4 days. The permit inspection usually follows within a few working days, and the system is usable the same day it is commissioned.
A heat pump costs about $11,500 installed for a 3-ton equivalent, against about $10,500 for a central AC and gas furnace — slightly more upfront, but it is one system instead of two, and it heats far more cheaply than electric resistance heat. In mild climates a heat pump is usually the cheapest option over 10 years, especially with utility rebates. In very cold climates, a cold-climate heat pump paired with a gas furnace (a dual-fuel system) gives the lowest running cost, because the furnace only fires on the coldest days.
Cost by state
Labor is the part of the price that moves most by location. These state editions re-price this guide with the local labor index, add city prices and the state-specific permit and code notes.
HVAC Replacement Cost in Texas
State-adjusted prices, city figures and Texas code notes.
Read the guideHVAC Replacement Cost in California
State-adjusted prices, city figures and California code notes.
Read the guideHVAC Replacement Cost in Florida
State-adjusted prices, city figures and Florida code notes.
Read the guideHVAC Replacement Cost in New York
State-adjusted prices, city figures and New York code notes.
Read the guideHVAC Replacement Cost in Pennsylvania
State-adjusted prices, city figures and Pennsylvania code notes.
Read the guideHVAC Replacement Cost in Illinois
State-adjusted prices, city figures and Illinois code notes.
Read the guideHVAC Replacement Cost in Ohio
State-adjusted prices, city figures and Ohio code notes.
Read the guideHVAC Replacement Cost in Georgia
State-adjusted prices, city figures and Georgia code notes.
Read the guideHVAC Replacement Cost in North Carolina
State-adjusted prices, city figures and North Carolina code notes.
Read the guideHVAC Replacement Cost in Michigan
State-adjusted prices, city figures and Michigan code notes.
Read the guideMore cost guides
Deck Build Cost
Materials and labor for a ground-level deck in pressure-treated lumber, cedar and composite, priced per square foot with railing and stair allowances.
Read the guideRoof Replacement Cost
Tear-off and replacement per roofing square for architectural shingles, metal and tile, including underlayment, flashing and disposal.
Read the guideBathroom Remodel Cost
Full and partial remodels at three finish levels, split between fixtures, tile, plumbing, electrical and labor.
Read the guide