(01) — Cost guide · Washington edition

Drywall Installation Cost in Washington (2026)

In Washington, drywall installation cost for the typical project costs about $1,600 — 10% above the national average of $1,450. The gap comes from labor: Washington labor runs at 1.22× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Washington numbers, city prices and code notes.

$1,050
low end in Washington — simple spec
$1,600
typical in Washington — most homeowners pay near this
$3,500
high end in Washington — premium materials, complex site
$2.47
per sq ft of board area, hung and finished to level 4, Washington-adjusted

Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Washington, derived from the national guide as explained below — always confirm with local quotes.

Washington prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Washington labor sits at 1.22× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Washington range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageWashingtonDifference
Low end$950$1,05010% above
Typical project$1,450$1,60010% above
High end$3,200$3,50010% above

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Washington.

Cost breakdown, Washington-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the Washington index of 1.22. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (Washington)Total
Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste $300 $0 $300
ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats $200 $0 $200
HangingBoard cut, lifted and screwed off on walls and ceiling $0 $550 $550
Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked $0 $500 $500
Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal $50 $50 $100
Total for the typical projectState-adjusted from the national breakdown above $550 $1,100 $1,650

Typical cost by city in Washington

Labor markets differ within a state too. These city figures apply each city's multiplier to the Washington typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Spokane$1,450
Vancouver$1,550
Tacoma$1,650
Seattle$1,750
Bellevue$1,800

Washington rules, climate and code that change the price

Washington pairs high labor costs with seismic code: the Seattle area sits in a high seismic design category, so decks, porches and remodels need hold-downs and lateral bracing that cheaper markets skip. The state energy code is among the strictest in the country, and western Washington's rain makes flashing, drainage and treated lumber specifications matter more than in dry climates. Frost depth is modest west of the Cascades (12–18 in) but deeper in the east.

Drywall Installation Cost in Washington: what to watch

How much does drywall installation cost in Washington? About $1,600 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 10% above the national typical of $1,450, with most Washington jobs landing between $1,050 and $3,500. Within the state, Bellevue runs about $1,800 and Seattle about $1,750, while Spokane runs about $1,450. Washington drywall work is a seismic and moisture job: the Seattle area sits in a high seismic design category, so walls need bracing and fastening schedules that cheaper markets skip. The state energy code is among the strictest in the country, and western Washington's rain makes moisture control matter — drywall goes up only after the building is dried in, or the board swells and the tape lifts. Seattle-area permits are thorough, and tight-lot access adds to the bill. Compare quotes on finish level and moisture plan, because those two items decide whether a Washington room looks crisp or shows every seam.

What to ask contractors in Washington

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: Washington cities and counties require permits for roofing, decks and structural work, with seismic detailing checked on decks and additions in the Puget Sound region. Energy-code compliance is reviewed on remodels and additions.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the Washington labor market: a quote far above the $1,600 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — Washington

How to read these numbers. Last updated October 2026 · Washington figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the Washington labor index of 1.22; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.