(01) — Cost guide · Virginia edition
Drywall Installation Cost in Virginia (2026)
In Virginia, drywall installation cost for the typical project costs about $1,500 — 2% above the national average of $1,450. The gap comes from labor: Virginia labor runs at 1.05× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Virginia numbers, city prices and code notes.
- $950
- low end in Virginia — simple spec
- $1,500
- typical in Virginia — most homeowners pay near this
- $3,250
- high end in Virginia — premium materials, complex site
- $2.30
- per sq ft of board area, hung and finished to level 4, Virginia-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Virginia, derived from the national guide as explained below — always confirm with local quotes.
Virginia prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Virginia labor sits at 1.05× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Virginia range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Virginia | Difference |
|---|---|---|---|
| Low end | $950 | $950 | 2% above |
| Typical project | $1,450 | $1,500 | 2% above |
| High end | $3,200 | $3,250 | 2% above |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Virginia.
Cost breakdown, Virginia-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Virginia index of 1.05. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Virginia) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $450 | $450 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $400 | $400 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $950 | $1,500 |
Typical cost by city in Virginia
Labor markets differ within a state too. These city figures apply each city's multiplier to the Virginia typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Richmond | $1,400 |
| Norfolk | $1,450 |
| Virginia Beach | $1,500 |
| Arlington | $1,650 |
| Alexandria | $1,650 |
Virginia rules, climate and code that change the price
Virginia's costs split between the Washington DC suburbs — Arlington and Alexandria run well above the state figure — and the rest of the state, which is near average. The statewide residential code applies with local enforcement; frost depth is 18–24 in in the north and less in the Tidewater, where hurricane wind and flood-zone rules govern coastal work. Termite protection is standard practice statewide.
Drywall Installation Cost in Virginia: what to watch
How much does drywall installation cost in Virginia? About $1,500 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 3% above the national typical of $1,450, with most Virginia jobs landing between $950 and $3,250. Within the state, Arlington runs about $1,700 and Alexandria about $1,650, while Richmond and Norfolk run about $1,450. Virginia drywall costs split between the Washington DC suburbs, where labor and permit scrutiny run 10–12% above the state figure, and the rest of the state, which sits near average. The statewide residential code applies with local enforcement, and termite protection is standard practice statewide — worth remembering where new framing goes up behind the board. In Tidewater flood zones, elevation and flood-vent rules can affect ground-level rooms, so confirm the room's flood status before the board goes up. HOA rules on finishes are widespread in the Northern Virginia suburbs. Confirm the finish level in writing before comparing prices.
What to ask contractors in Virginia
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Virginia counties require permits for roofing, decks and structural work. In Tidewater flood zones, elevation and flood-vent rules can affect ground-level structures and must be checked before a deck or addition is designed.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Virginia labor market: a quote far above the $1,500 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Virginia
Virginia counties require permits for roofing, decks and structural work. In Tidewater flood zones, elevation and flood-vent rules can affect ground-level structures and must be checked before a deck or addition is designed.
Virginia labor averages about 5% above national, but the DC suburbs run 10–12% above the state figure while Richmond and Norfolk sit slightly below it. Coastal wind and flood rules are the regional adders.
Budget around $1,500 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Virginia, with most jobs landing between $950 and $3,250. That typical figure is 2% above the national typical of $1,450, because Virginia labor runs at 1.05× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Virginia, the typical project runs from about $1,400 in Richmond to about $1,650 in Alexandria, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,700 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the Virginia typical of $1,500, with most Virginia jobs landing between $950 and $3,250. Arlington is the state's highest-cost drywall market, priced by the Washington DC suburbs, with thorough county permitting and HOA rules that are often stricter than the code. The statewide residential code applies with local enforcement, and termite protection belongs in the specification where new framing goes up.