(01) — Cost guide · Utah edition

Drywall Installation Cost in Utah (2026)

In Utah, drywall installation cost for the typical project costs about $1,450 — 1% below the national average of $1,450. The gap comes from labor: Utah labor runs at 0.98× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Utah numbers, city prices and code notes.

$950
low end in Utah — simple spec
$1,450
typical in Utah — most homeowners pay near this
$3,150
high end in Utah — premium materials, complex site
$2.23
per sq ft of board area, hung and finished to level 4, Utah-adjusted

Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Utah, derived from the national guide as explained below — always confirm with local quotes.

Utah prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Utah labor sits at 0.98× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Utah range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageUtahDifference
Low end$950$9501% below
Typical project$1,450$1,4501% below
High end$3,200$3,1501% below

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Utah.

Cost breakdown, Utah-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the Utah index of 0.98. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (Utah)Total
Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste $300 $0 $300
ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats $200 $0 $200
HangingBoard cut, lifted and screwed off on walls and ceiling $0 $450 $450
Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked $0 $400 $400
Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal $50 $50 $100
Total for the typical projectState-adjusted from the national breakdown above $550 $900 $1,450

Typical cost by city in Utah

Labor markets differ within a state too. These city figures apply each city's multiplier to the Utah typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
West Valley City$1,400
Provo$1,400
Orem$1,400
Salt Lake City$1,450
West Jordan$1,450

Utah rules, climate and code that change the price

Utah enforces a statewide residential code with local enforcement, and its Wasatch Front labor market sits just below the national average. Frost depth is 30–36 in along the Wasatch Front, snow loads rise sharply in mountain communities, and seismic requirements apply statewide with the highest categories along the Wasatch fault. Expansive soils in parts of the Salt Lake Valley affect footings.

Drywall Installation Cost in Utah: what to watch

How much does drywall installation cost in Utah? About $1,450 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, right on the national typical of $1,450, with most Utah jobs landing between $950 and $3,150. Within the state, Salt Lake City runs about $1,500 and West Jordan about $1,450, while West Valley City, Provo and Orem run about $1,400. Utah drywall work is an elevation job: frost depth is 30–36 in along the Wasatch Front, so footings sit deep, and snow loads rise sharply in mountain communities, where framing needs bracing for a heavy winter. Seismic requirements apply statewide, highest along the Wasatch fault, and expansive soils in parts of the Salt Lake Valley affect footings. The state enforces a statewide residential code with local enforcement, and the Wasatch Front labor market sits just below the national average. Get the finish level and moisture plan in writing — a quote pricing level 3 work against a level 4 specification is not a bargain.

What to ask contractors in Utah

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: Utah requires permits for roofing, decks and structural work under the statewide residential code, with seismic detailing checked along the Wasatch Front and snow-load checks in mountain jurisdictions.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the Utah labor market: a quote far above the $1,450 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — Utah

How to read these numbers. Last updated October 2026 · Utah figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the Utah labor index of 0.98; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.