(01) — Cost guide · Texas edition
Drywall Installation Cost in Texas (2026)
In Texas, drywall installation cost for the typical project costs about $1,400 — 3% below the national average of $1,450. The gap comes from labour: Texas labour runs at 0.94× the national average, and labour is about 45% of an installed price, so the state figure below scales the labour share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Texas numbers, city prices and code notes.
- $900
- low end in Texas — simple spec
- $1,400
- typical in Texas — most homeowners pay near this
- $3,100
- high end in Texas — premium materials, complex site
- $2.19
- per sq ft of board area, hung and finished to level 4, Texas-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Texas, derived from the national guide as explained below — always confirm with local quotes.
Texas prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labour is what moves, and Texas labour sits at 0.94× the national average. Applying that index to the labour share (about 45% of the installed price) gives the Texas range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labour market, and it is worth asking which line moved.
| Figure | National average | Texas | Difference |
|---|---|---|---|
| Low end | $950 | $900 | 3% below |
| Typical project | $1,450 | $1,400 | 3% below |
| High end | $3,200 | $3,100 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Texas.
Cost breakdown, Texas-adjusted
The national guide's line items, with materials held at national prices and labour scaled by the Texas index of 0.94. Compare a real bid against this table line by line: if a contractor's labour lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labour (Texas) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $400 | $400 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $400 | $400 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $850 | $1,400 |
Typical cost by city in Texas
Labour markets differ within a state too. These city figures apply each city's multiplier to the Texas typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| El Paso | $1,250 |
| San Antonio | $1,350 |
| Houston | $1,400 |
| Fort Worth | $1,400 |
| Dallas | $1,450 |
| Austin | $1,500 |
Texas rules, climate and code that change the price
Texas has no statewide general-contractor licence, so permit rules and inspection quality vary by city — Houston, Dallas and Austin all run their own permitting portals with different thresholds, and unincorporated areas may require no building permit at all. Frost depth is shallow across most of the state (often 6–12 in), which keeps footing work cheap, but expansive clay soils around Dallas–Fort Worth and Houston move with moisture and demand deeper, belled piers for decks and fences. Gulf Coast wind and hail exposure raises roofing and fence specifications, and hail-resistant shingles are a common insurance-driven upgrade.
Drywall Installation Cost in Texas: what to watch
Texas drywall is a humidity and movement job. Gulf Coast humidity means bathrooms and kitchens need moisture-resistant board, and the whole house needs proper taping and mudding that can cure in humid air — a rushed finish shows as cracks and nail pops within a season. Expansive clay soils around Dallas-Fort Worth and Houston move foundations, so drywall cracks at corners and ceilings are a recurring Texas complaint; a good installer uses corner bead, flexible joints where movement is expected, and a level-5 finish on walls that will catch raking light. Large open-plan homes mean more board per job, so compare quotes by sheet count and finish level, not by room.
What to ask contractors in Texas
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Most Texas cities require a permit for a roof replacement, a deck over 30 in high or attached to the house, and any structural work, but thresholds differ by city and unincorporated land often has none. Check the city permitting portal before work starts — an unpermitted deck or roof can stall a future sale even where enforcement is light.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labour basis: Ask how the quote treats the Texas labour market: a quote far above the $1,400 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Texas
Most Texas cities require a permit for a roof replacement, a deck over 30 in high or attached to the house, and any structural work, but thresholds differ by city and unincorporated land often has none. Check the city permitting portal before work starts — an unpermitted deck or roof can stall a future sale even where enforcement is light.
Texas labour runs about 6% below the national average, so installed prices sit slightly under national figures, but Austin runs roughly 8% above the state figure and Gulf Coast wind/hail specifications can erase the saving on roofing. Material prices are national; it is the labour line and the local code extras that move a Texas quote.
Budget around $1,400 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Texas, with most jobs landing between $900 and $3,100. That typical figure is 3% below the national typical of $1,450, because Texas labour runs at 0.94× the national average and labour is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Texas, the typical project runs from about $1,250 in El Paso to about $1,500 in Austin, reflecting local labour markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.