(01) — Cost guide · South Carolina edition
Drywall Installation Cost in South Carolina (2026)
In South Carolina, drywall installation cost for the typical project costs about $1,400 — 4% below the national average of $1,450. The gap comes from labor: South Carolina labor runs at 0.9× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the South Carolina numbers, city prices and code notes.
- $900
- low end in South Carolina — simple spec
- $1,400
- typical in South Carolina — most homeowners pay near this
- $3,050
- high end in South Carolina — premium materials, complex site
- $2.15
- per sq ft of board area, hung and finished to level 4, South Carolina-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in South Carolina, derived from the national guide as explained below — always confirm with local quotes.
South Carolina prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and South Carolina labor sits at 0.9× the national average. Applying that index to the labor share (about 45% of the installed price) gives the South Carolina range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | South Carolina | Difference |
|---|---|---|---|
| Low end | $950 | $900 | 4% below |
| Typical project | $1,450 | $1,400 | 4% below |
| High end | $3,200 | $3,050 | 4% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for South Carolina.
Cost breakdown, South Carolina-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the South Carolina index of 0.9. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (South Carolina) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $400 | $400 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $350 | $350 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $800 | $1,350 |
Typical cost by city in South Carolina
Labor markets differ within a state too. These city figures apply each city's multiplier to the South Carolina typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Columbia | $1,350 |
| Greenville | $1,350 |
| North Charleston | $1,400 |
| Myrtle Beach | $1,400 |
| Charleston | $1,450 |
South Carolina rules, climate and code that change the price
South Carolina is a low-cost labor market where hurricane wind rules govern the coast: the building code sets wind-speed and uplift requirements for roofing, decks and fences in coastal counties, and flood-zone rules affect ground-level structures. Frost depth is negligible in the Lowcountry and about 12 in upstate. Termite protection is standard statewide, and Charleston's historic-district rules can restrict roofing and fence materials in designated areas.
Drywall Installation Cost in South Carolina: what to watch
How much does drywall installation cost in South Carolina? About $1,400 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 3% below the national typical of $1,450, with most South Carolina jobs landing between $900 and $3,050. Within the state, Charleston runs about $1,450, while Columbia and Greenville run about $1,350 and North Charleston and Myrtle Beach about $1,400. South Carolina drywall work is a coast and humidity job: the state is a low-cost labor market, but hurricane wind rules govern the coast, with wind-speed and uplift requirements for roofing, decks and fences in coastal counties, and flood-zone rules affect ground-level structures. Frost depth is negligible in the Lowcountry and about 12 in upstate, so interior work runs year-round. Termite protection is standard statewide, worth remembering where new framing goes up behind the board, and Charleston's historic-district rules can restrict materials in designated areas. Compare quotes on finish level and the moisture plan, because humid summers punish board that goes up before the building is dried in.
What to ask contractors in South Carolina
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: South Carolina requires permits for roofing, decks and structural work under the statewide residential code. Coastal counties add wind-uplift and flood-zone checks, and Charleston historic districts add material restrictions.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the South Carolina labor market: a quote far above the $1,400 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — South Carolina
South Carolina requires permits for roofing, decks and structural work under the statewide residential code. Coastal counties add wind-uplift and flood-zone checks, and Charleston historic districts add material restrictions.
South Carolina labor runs about 10% below the national average, with Charleston slightly above the state figure. Coastal wind detailing and termite protection are the local extras.
Budget around $1,400 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in South Carolina, with most jobs landing between $900 and $3,050. That typical figure is 4% below the national typical of $1,450, because South Carolina labor runs at 0.9× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within South Carolina, the typical project runs from about $1,350 in Columbia to about $1,450 in Charleston, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,450 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the South Carolina typical of $1,400, with most South Carolina jobs landing between $900 and $3,050. Charleston is the state's highest-cost drywall market, running slightly above the state figure. Hurricane wind rules govern the coast and termite protection is standard statewide, and Charleston's historic-district rules can restrict materials in designated areas — compare finish level and moisture plan line by line.