(01) — Cost guide · Oregon edition
Drywall Installation Cost in Oregon (2026)
In Oregon, drywall installation cost for the typical project costs about $1,550 — 6% above the national average of $1,450. The gap comes from labor: Oregon labor runs at 1.14× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Oregon numbers, city prices and code notes.
- $1,000
- low end in Oregon — simple spec
- $1,550
- typical in Oregon — most homeowners pay near this
- $3,400
- high end in Oregon — premium materials, complex site
- $2.39
- per sq ft of board area, hung and finished to level 4, Oregon-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Oregon, derived from the national guide as explained below — always confirm with local quotes.
Oregon prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Oregon labor sits at 1.14× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Oregon range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Oregon | Difference |
|---|---|---|---|
| Low end | $950 | $1,000 | 6% above |
| Typical project | $1,450 | $1,550 | 6% above |
| High end | $3,200 | $3,400 | 6% above |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Oregon.
Cost breakdown, Oregon-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Oregon index of 1.14. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Oregon) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $500 | $500 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $450 | $450 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $1,050 | $1,600 |
Typical cost by city in Oregon
Labor markets differ within a state too. These city figures apply each city's multiplier to the Oregon typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Salem | $1,500 |
| Eugene | $1,500 |
| Gresham | $1,550 |
| Bend | $1,600 |
| Portland | $1,650 |
Oregon rules, climate and code that change the price
Oregon enforces a statewide residential code with a strong energy code, and its costs split between the rainy Willamette Valley — where flashing, drainage and rot-resistant detailing dominate — and the high desert east of the Cascades. Seismic requirements apply statewide, with the highest design categories on the coast. Frost depth is 12–18 in in the valley and deeper in the east, and wildfire-zone rules apply in the wildland-urban interface.
Drywall Installation Cost in Oregon: what to watch
How much does drywall installation cost in Oregon? About $1,550 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 7% above the national typical of $1,450, with most Oregon jobs landing between $1,000 and $3,400. Within the state, Portland runs about $1,650, Bend and Gresham about $1,600, while Salem and Eugene run about $1,500. Oregon drywall work is a rain and energy-code job: the Willamette Valley's steady rain makes flashing, drainage and rot-resistant detailing the specification to watch, and the board goes up only after the building is dried in, or it swells and the tape lifts. A strong energy code means insulation and air sealing sit inside the wall the board covers. Seismic requirements apply statewide, highest on the coast, and frost depth is 12–18 in in the valley, deeper east of the Cascades. Portland is the expensive end. Get the finish level and moisture plan in writing — a quote pricing level 3 work against a level 4 specification is not a bargain.
What to ask contractors in Oregon
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Oregon requires permits for roofing, decks and structural work under the statewide residential code, with seismic detailing and, in wildfire-interface areas, ember-resistant materials checked at review.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Oregon labor market: a quote far above the $1,550 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Oregon
Oregon requires permits for roofing, decks and structural work under the statewide residential code, with seismic detailing and, in wildfire-interface areas, ember-resistant materials checked at review.
Oregon labor runs about 14% above the national average, with Portland further above the state figure. Seismic hardware, energy-code detailing and rain-driven flashing work are the local adders.
Budget around $1,550 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Oregon, with most jobs landing between $1,000 and $3,400. That typical figure is 6% above the national typical of $1,450, because Oregon labor runs at 1.14× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Oregon, the typical project runs from about $1,500 in Salem to about $1,650 in Portland, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,650 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the Oregon typical of $1,550, with most Oregon jobs landing between $1,000 and $3,400. Portland is the state's highest-cost drywall market, priced by its labor market and thorough permitting. Willamette Valley rain makes flashing, drainage and rot-resistant detailing the specification to watch, and the strong energy code means insulation and air sealing sit inside the wall the board covers, with seismic requirements applying statewide.