(01) — Cost guide · New Jersey edition

Drywall Installation Cost in New Jersey (2026)

In New Jersey, drywall installation cost for the typical project costs about $1,600 — 10% above the national average of $1,450. The gap comes from labor: New Jersey labor runs at 1.22× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the New Jersey numbers, city prices and code notes.

$1,050
low end in New Jersey — simple spec
$1,600
typical in New Jersey — most homeowners pay near this
$3,500
high end in New Jersey — premium materials, complex site
$2.47
per sq ft of board area, hung and finished to level 4, New Jersey-adjusted

Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in New Jersey, derived from the national guide as explained below — always confirm with local quotes.

New Jersey prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and New Jersey labor sits at 1.22× the national average. Applying that index to the labor share (about 45% of the installed price) gives the New Jersey range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageNew JerseyDifference
Low end$950$1,05010% above
Typical project$1,450$1,60010% above
High end$3,200$3,50010% above

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for New Jersey.

Cost breakdown, New Jersey-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the New Jersey index of 1.22. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (New Jersey)Total
Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste $300 $0 $300
ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats $200 $0 $200
HangingBoard cut, lifted and screwed off on walls and ceiling $0 $550 $550
Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked $0 $500 $500
Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal $50 $50 $100
Total for the typical projectState-adjusted from the national breakdown above $550 $1,100 $1,650

Typical cost by city in New Jersey

Labor markets differ within a state too. These city figures apply each city's multiplier to the New Jersey typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Trenton$1,550
Paterson$1,600
Elizabeth$1,600
Newark$1,650
Jersey City$1,700

New Jersey rules, climate and code that change the price

New Jersey enforces the Uniform Construction Code statewide with licensed-contractor requirements and thorough municipal inspections, and its labor market is priced by proximity to New York City. Frost depth is 36 in, snow loads apply statewide, and coastal wind requirements affect the Shore. Permit fees and review times in the denser north-eastern municipalities are notably higher than in the south.

Drywall Installation Cost in New Jersey: what to watch

How much does drywall installation cost in New Jersey? About $1,600 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 10% above the national typical of $1,450, with most New Jersey jobs landing between $1,050 and $3,500. Within the state, Jersey City runs about $1,750 and Newark about $1,650, while Trenton runs about $1,550. New Jersey drywall work is a code and commuter-belt job: the Uniform Construction Code applies statewide with licensed-contractor requirements and thorough municipal inspections at footing, framing and final stages. The labor market is priced by proximity to New York City, and permit fees and review times in the denser north-eastern municipalities run notably higher than in the south. Coastal wind requirements affect the Shore, where moisture-resistant board is worth specifying in damp rooms. Confirm the contractor's registration and the finish level in writing, because a New Jersey quote that skips the level 4 specification is not comparable to one that includes it.

What to ask contractors in New Jersey

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: New Jersey requires permits for roofing, decks and structural work statewide under the Uniform Construction Code, with inspections at footing, framing and final stages. Contractors must be registered with the state.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the New Jersey labor market: a quote far above the $1,600 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — New Jersey

How to read these numbers. Last updated October 2026 · New Jersey figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the New Jersey labor index of 1.22; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.