(01) — Cost guide · Missouri edition
Drywall Installation Cost in Missouri (2026)
In Missouri, drywall installation cost for the typical project costs about $1,400 — 3% below the national average of $1,450. The gap comes from labor: Missouri labor runs at 0.93× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Missouri numbers, city prices and code notes.
- $900
- low end in Missouri — simple spec
- $1,400
- typical in Missouri — most homeowners pay near this
- $3,100
- high end in Missouri — premium materials, complex site
- $2.18
- per sq ft of board area, hung and finished to level 4, Missouri-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Missouri, derived from the national guide as explained below — always confirm with local quotes.
Missouri prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Missouri labor sits at 0.93× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Missouri range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Missouri | Difference |
|---|---|---|---|
| Low end | $950 | $900 | 3% below |
| Typical project | $1,450 | $1,400 | 3% below |
| High end | $3,200 | $3,100 | 3% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Missouri.
Cost breakdown, Missouri-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Missouri index of 0.93. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Missouri) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $400 | $400 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $350 | $350 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $850 | $1,400 |
Typical cost by city in Missouri
Labor markets differ within a state too. These city figures apply each city's multiplier to the Missouri typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Springfield | $1,300 |
| Columbia | $1,350 |
| Kansas City | $1,400 |
| Independence | $1,400 |
| St. Louis | $1,450 |
Missouri rules, climate and code that change the price
Missouri has no statewide residential building code — adoption is local, so St. Louis and Kansas City enforce thorough codes while many rural counties have minimal or no permitting for residential work. Frost depth is 24–30 in, tornado and severe-storm exposure makes storm-rated roofing a common upgrade, and expansive clay in the St. Louis area affects footings. Always verify the local jurisdiction's rules before assuming no permit is needed.
Drywall Installation Cost in Missouri: what to watch
How much does drywall installation cost in Missouri? About $1,400 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 3% below the national typical of $1,450, with most Missouri jobs landing between $900 and $3,100. Within the state, St. Louis runs about $1,450 and Kansas City about $1,400, while Springfield runs about $1,300 and Columbia about $1,350. Missouri drywall work is a code and storm job: the state has no statewide residential building code, so St. Louis and Kansas City enforce thorough codes while many rural counties have minimal or no permitting for residential work — always verify the local jurisdiction's rules before assuming no permit is needed. Frost depth is 24–30 in, tornado and severe-storm exposure makes storm-rated fasteners and bracing a common upgrade across the state, and expansive clay in the St. Louis area affects footings and the framing behind the board. Compare quotes on finish level and moisture plan, because those two items decide whether a Missouri room looks crisp or shows every seam.
What to ask contractors in Missouri
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Missouri leaves code adoption to local jurisdictions, so permit requirements vary more here than in most states: St. Louis and Kansas City are thorough, while some rural counties require little or nothing for residential work. Check the county or city, not the state, for your address.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Missouri labor market: a quote far above the $1,400 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Missouri
Missouri leaves code adoption to local jurisdictions, so permit requirements vary more here than in most states: St. Louis and Kansas City are thorough, while some rural counties require little or nothing for residential work. Check the county or city, not the state, for your address.
Missouri labor runs about 7% below the national average, with St. Louis slightly above the state figure. Storm-rated roofing and clay-soil footings are the local cost items.
Budget around $1,400 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Missouri, with most jobs landing between $900 and $3,100. That typical figure is 3% below the national typical of $1,450, because Missouri labor runs at 0.93× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Missouri, the typical project runs from about $1,300 in Springfield to about $1,450 in St. Louis, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,450 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the Missouri typical of $1,400, with most Missouri jobs landing between $900 and $3,100. St. Louis is the state's highest-cost drywall market, with the most thorough code enforcement in the state. Expansive clay soils in the St. Louis area affect footings and the framing behind the board, and tornado exposure makes storm-rated fasteners worth specifying.