(01) — Cost guide · Minnesota edition

Drywall Installation Cost in Minnesota (2026)

In Minnesota, drywall installation cost for the typical project costs about $1,450 — 1% above the national average of $1,450. The gap comes from labor: Minnesota labor runs at 1.02× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Minnesota numbers, city prices and code notes.

$950
low end in Minnesota — simple spec
$1,450
typical in Minnesota — most homeowners pay near this
$3,250
high end in Minnesota — premium materials, complex site
$2.27
per sq ft of board area, hung and finished to level 4, Minnesota-adjusted

Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Minnesota, derived from the national guide as explained below — always confirm with local quotes.

Minnesota prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Minnesota labor sits at 1.02× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Minnesota range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageMinnesotaDifference
Low end$950$9501% above
Typical project$1,450$1,4501% above
High end$3,200$3,2501% above

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Minnesota.

Cost breakdown, Minnesota-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the Minnesota index of 1.02. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (Minnesota)Total
Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste $300 $0 $300
ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats $200 $0 $200
HangingBoard cut, lifted and screwed off on walls and ceiling $0 $450 $450
Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked $0 $400 $400
Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal $50 $50 $100
Total for the typical projectState-adjusted from the national breakdown above $550 $950 $1,450

Typical cost by city in Minnesota

Labor markets differ within a state too. These city figures apply each city's multiplier to the Minnesota typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Rochester$1,400
Duluth$1,400
Bloomington$1,450
Minneapolis$1,500
St. Paul$1,500

Minnesota rules, climate and code that change the price

Minnesota enforces a statewide residential code with local enforcement and some of the deepest frost requirements in the country — 60 in in the north, 42 in in the Twin Cities — plus heavy snow loads and a strict energy code. Labor sits just above the national average, but deep footings, snow-load structure and energy-code insulation and air-sealing requirements make Minnesota quotes structurally more expensive than the labor index alone suggests.

Drywall Installation Cost in Minnesota: what to watch

How much does drywall installation cost in Minnesota? About $1,450 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, right on the national typical of $1,450, with most Minnesota jobs landing between $950 and $3,250. Within the state, Minneapolis and St. Paul both run about $1,500, Bloomington $1,450, while Rochester and Duluth run about $1,400. Minnesota drywall work is a frost and energy-code job: the state enforces a statewide residential code with the deepest frost requirements — 60 in in the north, 42 in in the Twin Cities — plus snow loads and a strict energy code. Labor sits just above the national average, but deep footings, snow-load structure and energy-code insulation and air sealing make Minnesota quotes costlier than labor alone suggests. That insulation and air sealing sit inside the wall the board covers, so the finish depends on the assembly behind it. Get the finish level and moisture plan in writing — a level 3 quote against a level 4 specification is not a bargain.

What to ask contractors in Minnesota

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: Minnesota requires permits for roofing, decks and structural work under the state residential code, with footing-depth, snow-load and energy-code checks standard. The Twin Cities enforce most thoroughly.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the Minnesota labor market: a quote far above the $1,450 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — Minnesota

How to read these numbers. Last updated October 2026 · Minnesota figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the Minnesota labor index of 1.02; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.