(01) — Cost guide · Maryland edition
Drywall Installation Cost in Maryland (2026)
In Maryland, drywall installation cost for the typical project costs about $1,550 — 5% above the national average of $1,450. The gap comes from labor: Maryland labor runs at 1.12× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Maryland numbers, city prices and code notes.
- $1,000
- low end in Maryland — simple spec
- $1,550
- typical in Maryland — most homeowners pay near this
- $3,350
- high end in Maryland — premium materials, complex site
- $2.37
- per sq ft of board area, hung and finished to level 4, Maryland-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Maryland, derived from the national guide as explained below — always confirm with local quotes.
Maryland prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Maryland labor sits at 1.12× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Maryland range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Maryland | Difference |
|---|---|---|---|
| Low end | $950 | $1,000 | 5% above |
| Typical project | $1,450 | $1,550 | 5% above |
| High end | $3,200 | $3,350 | 5% above |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Maryland.
Cost breakdown, Maryland-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Maryland index of 1.12. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Maryland) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $500 | $500 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $450 | $450 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $1,000 | $1,550 |
Typical cost by city in Maryland
Labor markets differ within a state too. These city figures apply each city's multiplier to the Maryland typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Frederick | $1,450 |
| Baltimore | $1,550 |
| Columbia | $1,600 |
| Germantown | $1,600 |
| Silver Spring | $1,650 |
Maryland rules, climate and code that change the price
Maryland's labor market is priced by the Washington DC suburbs, and the state enforces a statewide building code with county permitting. Frost depth is 24–30 in, coastal wind and flood rules apply around the Chesapeake Bay, and Maryland requires licensed contractors for home-improvement work above a threshold, with a state home-improvement license and a guaranty fund. Montgomery County and the DC suburbs are the highest-cost jurisdictions.
Drywall Installation Cost in Maryland: what to watch
How much does drywall installation cost in Maryland? About $1,550 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 5% above the national typical of $1,450, with most Maryland jobs landing between $1,000 and $3,350. Within the state, Silver Spring runs about $1,650 and Columbia and Germantown about $1,600, while Baltimore runs about $1,550 and Frederick about $1,450. Maryland drywall work is a code and commuter-belt job: the labor market is priced by the Washington DC suburbs, and the state enforces a statewide building code with county permitting. Maryland requires licensed contractors for home-improvement work above a threshold, with a state home-improvement license and a guaranty fund behind it, so the contractor's registration belongs in every quote. Frost depth is 24–30 in, and coastal wind and flood rules apply around the Chesapeake Bay and on the Eastern Shore. Montgomery County and the DC suburbs are the highest-cost jurisdictions in the state. Confirm the contractor's license and the finish level in writing before comparing prices.
What to ask contractors in Maryland
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Maryland requires permits for roofing, decks and structural work through county permitting offices, and home-improvement contractors must hold a state license. Chesapeake Bay coastal work adds wind and flood considerations.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Maryland labor market: a quote far above the $1,550 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Maryland
Maryland requires permits for roofing, decks and structural work through county permitting offices, and home-improvement contractors must hold a state license. Chesapeake Bay coastal work adds wind and flood considerations.
Maryland labor runs about 12% above the national average, with the DC suburbs further above the state figure. Licensed-contractor requirements and coastal detailing add cost beyond labor.
Budget around $1,550 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Maryland, with most jobs landing between $1,000 and $3,350. That typical figure is 5% above the national typical of $1,450, because Maryland labor runs at 1.12× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Maryland, the typical project runs from about $1,450 in Frederick to about $1,650 in Silver Spring, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,650 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the Maryland typical of $1,550, with most Maryland jobs landing between $1,000 and $3,350. Silver Spring is the state's highest-cost drywall market, priced by the Washington DC suburbs, with thorough county permitting. Maryland's licensed-contractor requirement means the contractor's state license belongs in every quote, and frost depth of 24–30 in governs the structure behind the board.