(01) — Cost guide · Louisiana edition
Drywall Installation Cost in Louisiana (2026)
In Louisiana, drywall installation cost for the typical project costs about $1,400 — 4% below the national average of $1,450. The gap comes from labor: Louisiana labor runs at 0.92× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Louisiana numbers, city prices and code notes.
- $900
- low end in Louisiana — simple spec
- $1,400
- typical in Louisiana — most homeowners pay near this
- $3,100
- high end in Louisiana — premium materials, complex site
- $2.17
- per sq ft of board area, hung and finished to level 4, Louisiana-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Louisiana, derived from the national guide as explained below — always confirm with local quotes.
Louisiana prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Louisiana labor sits at 0.92× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Louisiana range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Louisiana | Difference |
|---|---|---|---|
| Low end | $950 | $900 | 4% below |
| Typical project | $1,450 | $1,400 | 4% below |
| High end | $3,200 | $3,100 | 4% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Louisiana.
Cost breakdown, Louisiana-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Louisiana index of 0.92. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Louisiana) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $400 | $400 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $350 | $350 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $850 | $1,400 |
Typical cost by city in Louisiana
Labor markets differ within a state too. These city figures apply each city's multiplier to the Louisiana typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Shreveport | $1,300 |
| Lafayette | $1,350 |
| Lake Charles | $1,350 |
| Baton Rouge | $1,400 |
| New Orleans | $1,450 |
Louisiana rules, climate and code that change the price
Louisiana enforces a statewide residential code, and its cost drivers are water and wind: hurricane wind requirements govern roofing and exterior structures statewide, flood-zone elevation rules affect ground-level work, and the high water table and soft soils complicate footings and drainage. Frost is negligible. New Orleans adds historic-district material restrictions in older neighborhoods.
Drywall Installation Cost in Louisiana: what to watch
How much does drywall installation cost in Louisiana? About $1,400 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 3% below the national typical of $1,450, with most Louisiana jobs landing between $900 and $3,100. Within the state, New Orleans runs about $1,450, Baton Rouge about $1,400, while Shreveport runs about $1,300 and Lafayette and Lake Charles about $1,350. Louisiana drywall work is a water and wind job: the state enforces a statewide residential code; hurricane wind requirements govern roofs and exteriors statewide, flood-zone elevation rules affect ground-level work, and a high water table and soft soils complicate footings and drainage. Frost is negligible, but humid Gulf air makes the moisture plan the specification that matters: board that goes up before the building is dried in swells and the tape lifts. New Orleans adds historic-district material restrictions in older neighborhoods. Compare finish level and the moisture plan, because those two items decide whether a Louisiana room looks crisp or shows every seam.
What to ask contractors in Louisiana
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Louisiana requires permits for roofing, decks and structural work under the statewide residential code, with wind and flood-zone checks prominent in coastal parishes. Historic districts in New Orleans add material restrictions.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Louisiana labor market: a quote far above the $1,400 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Louisiana
Louisiana requires permits for roofing, decks and structural work under the statewide residential code, with wind and flood-zone checks prominent in coastal parishes. Historic districts in New Orleans add material restrictions.
Louisiana labor runs about 8% below the national average, with New Orleans slightly above the state figure. Wind-rated roofing, flood-zone detailing and drainage work are the local extras.
Budget around $1,400 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Louisiana, with most jobs landing between $900 and $3,100. That typical figure is 4% below the national typical of $1,450, because Louisiana labor runs at 0.92× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Louisiana, the typical project runs from about $1,300 in Shreveport to about $1,450 in New Orleans, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,450 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the Louisiana typical of $1,400, with most Louisiana jobs landing between $900 and $3,100. New Orleans is the state's highest-cost drywall market, running slightly above the state figure. Hurricane wind requirements govern exterior structures statewide, and the high water table and soft soils complicate footings and drainage, with historic-district material restrictions in older neighborhoods — get the finish level and moisture plan in writing.