(01) — Cost guide · Georgia edition
Drywall Installation Cost in Georgia (2026)
In Georgia, drywall installation cost for the typical project costs about $1,400 — 4% below the national average of $1,450. The gap comes from labour: Georgia labour runs at 0.92× the national average, and labour is about 45% of an installed price, so the state figure below scales the labour share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Georgia numbers, city prices and code notes.
- $900
- low end in Georgia — simple spec
- $1,400
- typical in Georgia — most homeowners pay near this
- $3,100
- high end in Georgia — premium materials, complex site
- $2.17
- per sq ft of board area, hung and finished to level 4, Georgia-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Georgia, derived from the national guide as explained below — always confirm with local quotes.
Georgia prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labour is what moves, and Georgia labour sits at 0.92× the national average. Applying that index to the labour share (about 45% of the installed price) gives the Georgia range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labour market, and it is worth asking which line moved.
| Figure | National average | Georgia | Difference |
|---|---|---|---|
| Low end | $950 | $900 | 4% below |
| Typical project | $1,450 | $1,400 | 4% below |
| High end | $3,200 | $3,100 | 4% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Georgia.
Cost breakdown, Georgia-adjusted
The national guide's line items, with materials held at national prices and labour scaled by the Georgia index of 0.92. Compare a real bid against this table line by line: if a contractor's labour lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labour (Georgia) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $400 | $400 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $350 | $350 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $850 | $1,400 |
Typical cost by city in Georgia
Labour markets differ within a state too. These city figures apply each city's multiplier to the Georgia typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Augusta | $1,300 |
| Columbus | $1,300 |
| Macon | $1,300 |
| Savannah | $1,350 |
| Athens | $1,350 |
| Atlanta | $1,450 |
Georgia rules, climate and code that change the price
Georgia's climate driver is humidity, heat and summer storms rather than frost — frost depth is only about 12 in in the north and negligible in the south, so footings are shallow and cheap. The state residential code applies statewide with local amendments, and Atlanta-area jurisdictions are the strictest on permits and inspections. Termite protection is a real line item here: soil treatment and borate-treated framing are standard practice, and coastal wind requirements apply around Savannah.
Drywall Installation Cost in Georgia: what to watch
Georgia drywall is a humidity and growth-market job. Atlanta and its suburbs are building and remodelling at a pace that keeps crews busy, which makes scheduling — not material — the scarce resource, and moisture-resistant board in bathrooms, kitchens and laundry rooms is essential in a climate where summer humidity rarely drops. Newer subdivisions are mostly drywall throughout, so repairs are straightforward, but older Atlanta bungalows and Savannah homes mix plaster and drywall, and matching texture across a repair is a skill worth paying for. Storm-driven roof leaks are the usual cause of board damage here; any board that has been wet should be cut out, not painted over, because mould grows inside the cavity.
What to ask contractors in Georgia
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Georgia counties and cities require permits for roofing, decks and structural work under the state residential code, with Atlanta-area jurisdictions the most thorough. Termite protection measures are typically inspected as part of framing work.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labour basis: Ask how the quote treats the Georgia labour market: a quote far above the $1,400 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Georgia
Georgia counties and cities require permits for roofing, decks and structural work under the state residential code, with Atlanta-area jurisdictions the most thorough. Termite protection measures are typically inspected as part of framing work.
Georgia labour runs about 8% below the national average, with Atlanta roughly 4% above the state figure. Shallow footings keep groundwork cheap; the local extras are termite protection and, near the coast, wind-rated connections.
Budget around $1,400 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Georgia, with most jobs landing between $900 and $3,100. That typical figure is 4% below the national typical of $1,450, because Georgia labour runs at 0.92× the national average and labour is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Georgia, the typical project runs from about $1,300 in Augusta to about $1,450 in Atlanta, reflecting local labour markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.