(01) — Cost guide · Connecticut edition
Drywall Installation Cost in Connecticut (2026)
In Connecticut, drywall installation cost for the typical project costs about $1,600 — 11% above the national average of $1,450. The gap comes from labor: Connecticut labor runs at 1.24× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Connecticut numbers, city prices and code notes.
- $1,050
- low end in Connecticut — simple spec
- $1,600
- typical in Connecticut — most homeowners pay near this
- $3,550
- high end in Connecticut — premium materials, complex site
- $2.49
- per sq ft of board area, hung and finished to level 4, Connecticut-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Connecticut, derived from the national guide as explained below — always confirm with local quotes.
Connecticut prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Connecticut labor sits at 1.24× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Connecticut range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Connecticut | Difference |
|---|---|---|---|
| Low end | $950 | $1,050 | 11% above |
| Typical project | $1,450 | $1,600 | 11% above |
| High end | $3,200 | $3,550 | 11% above |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Connecticut.
Cost breakdown, Connecticut-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Connecticut index of 1.24. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Connecticut) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $550 | $550 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $500 | $500 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $1,150 | $1,650 |
Typical cost by city in Connecticut
Labor markets differ within a state too. These city figures apply each city's multiplier to the Connecticut typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Hartford | $1,550 |
| Waterbury | $1,550 |
| New Haven | $1,600 |
| Bridgeport | $1,650 |
| Stamford | $1,750 |
Connecticut rules, climate and code that change the price
Connecticut enforces a statewide building code with thorough municipal inspections and a labor market priced by proximity to New York City — Stamford and the Fairfield County corridor run highest. Frost depth is 42 in, snow loads apply statewide, and coastal wind requirements affect the Long Island Sound shore. Permit fees and review times in the larger cities are substantial.
Drywall Installation Cost in Connecticut: what to watch
How much does drywall installation cost in Connecticut? About $1,600 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 10% above the national typical of $1,450, with most Connecticut jobs landing between $1,050 and $3,550. Within the state, Stamford runs about $1,750, Bridgeport about $1,650 and New Haven about $1,600, while Hartford and Waterbury run about $1,550. Connecticut drywall work carries one of the highest labor premiums in the program, about 24% above the national average and priced by proximity to New York City, with Stamford and the Fairfield County corridor highest. The state enforces a statewide building code with thorough municipal inspections, with substantial permit fees and review times in the larger cities. Frost depth is 42 in, so footings sit three and a half feet down, snow loads apply statewide, and coastal wind requirements affect the Long Island Sound shore. Get the finish level and moisture plan in writing — a quote pricing level 3 work against a level 4 specification is not a bargain.
What to ask contractors in Connecticut
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Connecticut requires permits for roofing, decks and structural work statewide, with footing-depth and snow-load checks standard. Coastal towns add wind requirements for shoreline properties.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Connecticut labor market: a quote far above the $1,600 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Connecticut
Connecticut requires permits for roofing, decks and structural work statewide, with footing-depth and snow-load checks standard. Coastal towns add wind requirements for shoreline properties.
Connecticut labor runs about 24% above the national average, with Stamford roughly 10% above the state figure. Deep frost footings and coastal wind detailing add cost on top of the labor premium.
Budget around $1,600 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Connecticut, with most jobs landing between $1,050 and $3,550. That typical figure is 11% above the national typical of $1,450, because Connecticut labor runs at 1.24× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Connecticut, the typical project runs from about $1,550 in Hartford to about $1,750 in Stamford, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,750 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, above the Connecticut typical of $1,600, with most Connecticut jobs landing between $1,050 and $3,550. Stamford is the state's highest-cost drywall market, priced by the Fairfield County corridor and its proximity to New York City. Frost depth of 42 in means footings must sit three and a half feet down, and snow loads plus coastal wind requirements shape the structure — compare finish level and moisture plan line by line.