(01) — Cost guide · Colorado edition

Drywall Installation Cost in Colorado (2026)

In Colorado, drywall installation cost for the typical project costs about $1,500 — 4% above the national average of $1,450. The gap comes from labor: Colorado labor runs at 1.08× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Colorado numbers, city prices and code notes.

$1,000
low end in Colorado — simple spec
$1,500
typical in Colorado — most homeowners pay near this
$3,300
high end in Colorado — premium materials, complex site
$2.33
per sq ft of board area, hung and finished to level 4, Colorado-adjusted

Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Colorado, derived from the national guide as explained below — always confirm with local quotes.

Colorado prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Colorado labor sits at 1.08× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Colorado range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageColoradoDifference
Low end$950$1,0004% above
Typical project$1,450$1,5004% above
High end$3,200$3,3004% above

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Colorado.

Cost breakdown, Colorado-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the Colorado index of 1.08. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (Colorado)Total
Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste $300 $0 $300
ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats $200 $0 $200
HangingBoard cut, lifted and screwed off on walls and ceiling $0 $500 $500
Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked $0 $450 $450
Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal $50 $50 $100
Total for the typical projectState-adjusted from the national breakdown above $550 $1,000 $1,500

Typical cost by city in Colorado

Labor markets differ within a state too. These city figures apply each city's multiplier to the Colorado typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Colorado Springs$1,450
Aurora$1,500
Fort Collins$1,500
Denver$1,550
Boulder$1,650

Colorado rules, climate and code that change the price

Colorado's Front Range labor market runs above average, and its cost drivers are altitude and soil: expansive bentonite soils along the Front Range shift foundations and fence posts unless footings are engineered, hail is a frequent roofing cost driver (impact-resistant shingles are common and sometimes insurance-required), and frost depth is 36 in with snow loads that rise sharply in the mountains. Wildfire-zone rules apply in the foothills and mountain communities.

Drywall Installation Cost in Colorado: what to watch

How much does drywall installation cost in Colorado? About $1,500 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 3% above the national typical of $1,450, with most Colorado jobs landing between $1,000 and $3,300. Within the state, Boulder runs about $1,650 and Denver about $1,550, while Aurora and Fort Collins run about $1,500 and Colorado Springs about $1,450. Colorado drywall work is an altitude and soil job: Front Range labor runs above average, and expansive bentonite soils along the Front Range shift foundations and fence posts unless footings are engineered — and the framing behind the board inherits that movement. Hail is a frequent roofing cost driver, with impact-resistant shingles common and sometimes insurance-required; frost depth is 36 in, with snow loads rising sharply in the mountains. Wildfire-zone rules apply in the foothills and mountain communities. Compare finish level, dust control and the moisture plan line by line, and be suspicious of any quote pricing level 3 work against a level 4 specification.

What to ask contractors in Colorado

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: Colorado cities and counties require permits for roofing, decks and structural work, with expansive-soil footing design and, in foothill communities, wildfire-resistant materials checked at permit review.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the Colorado labor market: a quote far above the $1,500 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — Colorado

How to read these numbers. Last updated October 2026 · Colorado figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the Colorado labor index of 1.08; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.