(01) — Cost guide · Alabama edition
Drywall Installation Cost in Alabama (2026)
In Alabama, drywall installation cost for the typical project costs about $1,350 — 6% below the national average of $1,450. The gap comes from labor: Alabama labor runs at 0.86× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Alabama numbers, city prices and code notes.
- $900
- low end in Alabama — simple spec
- $1,350
- typical in Alabama — most homeowners pay near this
- $3,000
- high end in Alabama — premium materials, complex site
- $2.11
- per sq ft of board area, hung and finished to level 4, Alabama-adjusted
Typical project used for these figures: hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish. Ranges are 2026 planning figures for a professional installation in Alabama, derived from the national guide as explained below — always confirm with local quotes.
Alabama prices vs the national average
Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Alabama labor sits at 0.86× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Alabama range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.
| Figure | National average | Alabama | Difference |
|---|---|---|---|
| Low end | $950 | $900 | 6% below |
| Typical project | $1,450 | $1,350 | 6% below |
| High end | $3,200 | $3,000 | 6% below |
For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national drywall installation cost guide. The table below re-prices that same breakdown for Alabama.
Cost breakdown, Alabama-adjusted
The national guide's line items, with materials held at national prices and labor scaled by the Alabama index of 0.86. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.
| Line item | Materials | Labor (Alabama) | Total |
|---|---|---|---|
| Drywall sheets20 sheets of 4 × 8 ft, 1/2 in standard board, including cutting waste | $300 | $0 | $300 |
| ConsumablesScrews, joint tape, corner bead and about 5 gallons of compound across coats | $200 | $0 | $200 |
| HangingBoard cut, lifted and screwed off on walls and ceiling | $0 | $400 | $400 |
| Taping & finishingTape coat, fill coat and finish coat to level 4, feathered and checked | $0 | $350 | $350 |
| Sanding, texture-ready prep & cleanupFinal sand, dust control, scrap removal | $50 | $50 | $100 |
| Total for the typical projectState-adjusted from the national breakdown above | $550 | $800 | $1,300 |
Typical cost by city in Alabama
Labor markets differ within a state too. These city figures apply each city's multiplier to the Alabama typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.
| City | Typical project cost |
|---|---|
| Montgomery | $1,300 |
| Tuscaloosa | $1,300 |
| Birmingham | $1,350 |
| Huntsville | $1,350 |
| Mobile | $1,350 |
Alabama rules, climate and code that change the price
Alabama is one of the lowest-cost labor markets in the program, but it has no statewide residential building code — adoption is local, so permit practice ranges from thorough in Birmingham and Huntsville to minimal in rural counties. Frost is negligible, tornado and hurricane exposure in the south and Gulf Coast makes storm-rated roofing a common upgrade, and termite protection is standard statewide.
Drywall Installation Cost in Alabama: what to watch
How much does drywall installation cost in Alabama? About $1,350 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, about 7% below the national typical of $1,450, with most Alabama jobs landing between $900 and $3,000. Within the state, Birmingham and Huntsville both run about $1,350, while Mobile runs about $1,300 and Montgomery and Tuscaloosa about $1,300. Alabama drywall work is cheap labor with a code caveat: one of the lowest-cost labor markets in the program, but it has no statewide residential building code — adoption is local, so permit practice ranges from thorough in Birmingham and Huntsville to minimal in rural counties. Frost is negligible, so interior work runs year-round, while tornado and hurricane exposure in the south and Gulf Coast makes storm-rated roofing a common upgrade. Termite protection is standard statewide, worth remembering where new framing goes up behind the board. Compare finish level and the moisture plan, because those two items decide whether an Alabama room looks crisp or shows every seam.
What to ask contractors in Alabama
Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.
- Permit: Alabama leaves code adoption to local jurisdictions, so permit requirements vary: Birmingham, Huntsville and Mobile enforce thoroughly, while some rural counties require little for residential work. Check the city or county for your address.
- Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
- Labor basis: Ask how the quote treats the Alabama labor market: a quote far above the $1,350 typical figure should name the extra work, access problem or specification that justifies it.
- Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.
Frequently asked questions — Alabama
Alabama leaves code adoption to local jurisdictions, so permit requirements vary: Birmingham, Huntsville and Mobile enforce thoroughly, while some rural counties require little for residential work. Check the city or county for your address.
Alabama labor runs about 14% below the national average and is even across its cities. Storm-rated roofing and termite protection are the local extras; shallow footings keep groundwork cheap.
Budget around $1,350 for the typical project (hanging and finishing a 12 × 16 ft room (walls and ceiling, about 640 sq ft of board, 20 sheets) to a level 4 finish) in Alabama, with most jobs landing between $900 and $3,000. That typical figure is 6% below the national typical of $1,450, because Alabama labor runs at 0.86× the national average and labor is about 45% of the installed price. Get at least three local quotes before committing — the range above is a planning figure, not a bid.
Yes. Within Alabama, the typical project runs from about $1,300 in Montgomery to about $1,350 in Mobile, reflecting local labor markets and, where applicable, stricter local code requirements. The city figures above are planning estimates from the state average, not quotes — a specific job's price depends on its specification, access and site conditions.
About $1,350 for hanging and finishing a 12×16 ft room — walls and ceiling, about 640 sq ft of board, 20 sheets — to a level 4 finish, right on the Alabama typical of $1,350, with most Alabama jobs landing between $900 and $3,000. Birmingham runs at the state figure alongside Huntsville, with the most thorough permitting in the state. Alabama has no statewide residential code, so permit practice varies by city, and termite protection is standard statewide, with storm-rated roofing a common upgrade in the south and Gulf Coast — compare finish level and moisture plan line by line.