(01) — Cost guide · Colorado edition

Deck Build Cost in Colorado (2026)

In Colorado, deck build cost for the typical project costs about $8,900 — 4% above the national average of $8,600. The gap comes from labor: Colorado labor runs at 1.08× the national average, and labor is about 45% of an installed price, so the state figure below scales the labor share only and leaves material prices at national levels. Read the national guide for the full breakdown, then use this page for the Colorado numbers, city prices and code notes.

$4,350
low end in Colorado — simple spec
$8,900
typical in Colorado — most homeowners pay near this
$18,150
high end in Colorado — premium materials, complex site
$27.97
per sq ft installed, typical pressure-treated build, Colorado-adjusted

Typical project used for these figures: a 16 × 20 ft (320 sq ft) ground-level deck in pressure-treated lumber, one set of steps, railing on three sides. Ranges are 2026 planning figures for a professional installation in Colorado, derived from the national guide as explained below — always confirm with local quotes.

Colorado prices vs the national average

Materials for this project are priced nationally — a bundle of shingles or a pallet of panels costs roughly the same anywhere in the country before delivery. Labor is what moves, and Colorado labor sits at 1.08× the national average. Applying that index to the labor share (about 45% of the installed price) gives the Colorado range below. If your quotes cluster well outside it, the difference is usually specification — material grade, code extras or site difficulty — not the labor market, and it is worth asking which line moved.

FigureNational averageColoradoDifference
Low end$4,200$4,3504% above
Typical project$8,600$8,9004% above
High end$17,500$18,1504% above

For the full national breakdown — what is included, what is billed separately, DIY vs pro, and what drives the price — read the national deck build cost guide. The table below re-prices that same breakdown for Colorado.

Cost breakdown, Colorado-adjusted

The national guide's line items, with materials held at national prices and labor scaled by the Colorado index of 1.08. Compare a real bid against this table line by line: if a contractor's labor lines run far above these figures, ask what is different about the job, and if the materials lines run far above, ask for the product grades.

Line itemMaterialsLabor (Colorado)Total
Footings & concreteDug or augered holes below frost depth, poured concrete, post bases $450 $600 $1,050
Framing lumber & beamsLedger, beams, joists, blocking and posts $1,100 $950 $2,050
Decking boardsPressure-treated boards, laid straight with a waste allowance $1,300 $1,200 $2,500
Railing & balustersThree sides, code-height rail with balusters $650 $600 $1,250
StepsOne set of steps with stringers and treads $350 $450 $800
Hardware, fasteners & flashingJoist hangers, structural screws, ledger flashing $400 $150 $550
Permits, plans & disposalBuilding permit, simple plan set, offcut and packaging disposal $450 $250 $700
Total for the typical projectState-adjusted from the national breakdown above $4,700 $4,200 $8,900

Typical cost by city in Colorado

Labor markets differ within a state too. These city figures apply each city's multiplier to the Colorado typical price for the same project — use them to sanity-check a quote from a specific metro, not as a bid. Rural areas outside these metros often land below the cheapest city shown, while resort and island markets can exceed the highest.

CityTypical project cost
Colorado Springs$8,550
Aurora$8,900
Fort Collins$8,900
Denver$9,250
Boulder$9,800

Colorado rules, climate and code that change the price

Colorado's Front Range labor market runs above average, and its cost drivers are altitude and soil: expansive bentonite soils along the Front Range shift foundations and fence posts unless footings are engineered, hail is a frequent roofing cost driver (impact-resistant shingles are common and sometimes insurance-required), and frost depth is 36 in with snow loads that rise sharply in the mountains. Wildfire-zone rules apply in the foothills and mountain communities.

Deck Build Cost in Colorado: what to watch

How much does a deck cost in Colorado? About $8,900 for a typical 16×20 ft (320 sq ft) ground-level pressure-treated deck — about 3% above the national typical of $8,600 — with most Colorado jobs landing between $4,350 and $18,150. Within the state, Boulder runs about $9,800 and Denver about $9,250, while Colorado Springs runs about $8,550. Colorado deck building is an altitude and soil job: expansive bentonite soils along the Front Range shift foundations and posts unless footings are engineered for them, so get the footing design in writing before comparing prices. Frost depth is 36 in, and snow loads rise sharply in the mountains, so posts must sit deep and railings need bracing that holds through a heavy winter. Hail punishes soft decking materials, and impact-resistant boards are a common upgrade, and wildfire-zone rules in the foothills and mountain communities can restrict combustible decking near the home. Boulder is the expensive end, priced by its Front Range labor market and thorough permitting.

What to ask contractors in Colorado

Four questions that catch the expensive surprises on this project in this state. Get the answers in writing, on the quote, before you compare prices — two quotes are only comparable when they describe the same job.

  • Permit: Colorado cities and counties require permits for roofing, decks and structural work, with expansive-soil footing design and, in foothill communities, wildfire-resistant materials checked at permit review.
  • Specification: Ask for the full material specification — grades, ratings and the code extras in the state notes above — not just a brand name and a total.
  • Labor basis: Ask how the quote treats the Colorado labor market: a quote far above the $8,900 typical figure should name the extra work, access problem or specification that justifies it.
  • Local references: Ask for two recent jobs in your city, not just your state — city prices above vary by thousands, and a contractor working regularly in your metro knows its permit office and inspectors.

Frequently asked questions — Colorado

How to read these numbers. Last updated October 2026 · Colorado figures are derived from the national guide by scaling the labor share (about 45% of the installed price) by the Colorado labor index of 1.08; materials are held at national prices. State indices are planning-grade figures compiled from published regional cost data, not contractor quotes. Always confirm with local quotes; your quote will vary.