Article — How-To · November 18, 2026 · 15 min read

Whole-House Fan Guide: Sizing, Installation and Real Cooling Savings

A whole-house fan costs $1,000 to $2,500 installed, uses about 10 percent of the electricity of central air conditioning, and can cut cooling costs by 50 to 90 percent in climates with cool evenings.

A whole-house fan costs $1,000 to $2,500 installed, uses about 10 percent of the electricity of central air conditioning, and can cut cooling costs by 50 to 90 percent in climates with cool evenings. The fan mounts in the ceiling, pulls cool evening air through open windows, and pushes hot air out through the attic, dropping the indoor temperature 10 to 20 degrees Fahrenheit (5.5 to 11 degrees Celsius) in 30 minutes. Sizing is the number that matters: a fan must move 3 to 5 cubic feet per minute (CFM) for every square foot of living space, so a 1,500 sq ft home needs 4,500 to 7,500 CFM. Check your attic ventilation first with the attic ventilation guide, size the insulation around it with the Insulation Calculator, and keep the heating system in shape with the furnace maintenance guide.

Whole-house fan installed in a hallway ceiling with the grille open, pulling cool evening air through an open window in a bright home interior

How does a whole-house fan work?

A whole-house fan works by pulling cool outdoor air through open windows and pushing hot indoor air out through the attic, and it cools a house in 30 minutes on a summer evening when the outside temperature drops below the indoor temperature. The fan mounts in the ceiling of a central hallway or landing, usually on the top floor, and when it runs, it draws air from every room with an open window, sweeps the heat out of the house, and exhausts it through the attic vents. The fan also flushes the attic, which can reach 130 to 150 degrees Fahrenheit (54 to 66 degrees Celsius) on a summer afternoon, and that hot attic radiates heat down into the living space all night. A whole-house fan is not an attic fan: an attic fan only ventilates the attic, while a whole-house fan ventilates the whole house and the attic together. A whole-house fan is also not a swamp cooler: it adds no moisture to the air, and it works best in dry climates and in any climate on evenings when the outdoor air is cooler than the indoor air.

The fan works best when the outdoor temperature is at least 5 degrees Fahrenheit (3 degrees Celsius) cooler than the indoor temperature, which is true on most summer evenings in the northern and central United States, and on many evenings in the South and Southwest. Run the fan for 1 to 2 hours in the evening, then turn it off and close the windows before the morning warms up, which traps the cool air inside for the next day. Open windows on the cool, shaded side of the house and in the rooms you use most, and open them 4 to 6 in (10 to 15 cm) wide, because a window open too far lets the air rush through one room and starve the others. Close the windows in rooms you do not want cooled, and never run the fan with all the windows closed, because the fan will pull air down the chimney, through the water heater flue, and through any gas appliance vent, which can pull carbon monoxide into the house. A whole-house fan uses 200 to 700 watts, which is about the same as a few light bulbs, while central air conditioning uses 3,000 to 5,000 watts, so the fan costs 2 to 5 cents an hour to run compared with 30 to 60 cents an hour for air conditioning.

What size whole-house fan do I need?

A whole-house fan must move 3 to 5 cubic feet per minute (CFM) for every square foot of living space, so a 1,000 sq ft home needs 3,000 to 5,000 CFM, a 1,500 sq ft home needs 4,500 to 7,500 CFM, and a 2,000 sq ft home needs 6,000 to 10,000 CFM. The lower end of the range suits a home with good insulation and shaded windows, while the upper end suits a home with a hot attic, west-facing windows, or a second floor that runs warm. Size the fan to the living space only, not the garage or the basement, and measure the square footage from the floor plans or a tape measure, not from a guess. A fan that is too small will run all evening and never drop the temperature more than a few degrees, while a fan that is too large will be loud, will pull doors shut, and will waste electricity. Most manufacturers publish a sizing chart by square footage, and the two-speed models are worth the extra $100 to $200, because the low speed is quiet enough to run while you sleep and the high speed cools the house fast in the evening.

The attic ventilation must match the fan, because the fan pushes 5,000 to 10,000 CFM of air into the attic and that air has to get out. A whole-house fan needs at least 1 sq ft (0.09 sq m) of net free vent area for every 750 CFM of fan capacity, so a 6,000 CFM fan needs 8 sq ft of vent area, and a 10,000 CFM fan needs 13 sq ft. Measure the existing vents: a typical ridge vent gives about 18 sq in of net free area per linear foot, a soffit vent gives about 50 to 70 sq in, and a gable vent gives 100 to 200 sq in depending on its size. If the attic does not have enough vent area, the fan will pressurize the attic, push hot air back down through the ceiling, and work against itself. Add more soffit vents or a second ridge vent before you install the fan, and check the full ventilation picture in the attic ventilation guide. The fan also needs a clear path from the ceiling to the attic, so check that insulation is not blocking the soffit vents, and that the attic has at least 3 ft (0.9 m) of clearance above the fan for the duct or the fan housing.

How much does a whole-house fan cost?

A whole-house fan costs $1,000 to $2,500 installed, with the fan itself costing $400 to $1,200 and professional installation costing $500 to $1,300. A basic direct-drive fan costs $400 to $700 and moves 3,000 to 5,000 CFM, a belt-drive fan costs $600 to $1,000 and moves 5,000 to 8,000 CFM more quietly, and a ducted, insulated fan costs $800 to $1,200 and moves 5,000 to 10,000 CFM with the least noise. A do-it-yourself installation saves $500 to $1,300 in labor, but it needs a new electrical circuit, a ceiling cut, and attic work, so most homeowners hire an electrician and a handyman together. The payback is fast: a whole-house fan saves $200 to $600 a year on cooling in a typical home, so it pays for itself in 2 to 5 years, and it lasts 15 to 25 years with basic maintenance. Running costs are 2 to 5 cents an hour, or $10 to $30 a summer, compared with $300 to $800 a summer for central air conditioning in the same home.

The total cost depends on the fan size, the ducting, and the electrical work. A fan that mounts directly in the ceiling with no ducting is the cheapest install, because it needs only a ceiling cut, a frame, and a power connection. A ducted fan costs $200 to $400 more, because it needs insulated ducting to carry the air to a remote exhaust point, but it is quieter, because the motor sits away from the living space. Adding a new 15-amp electrical circuit costs $150 to $400 if the panel has space, and adding a timer or a thermostat costs $50 to $150. A powered attic vent to boost the exhaust costs $200 to $400, but it is rarely needed if the attic ventilation is sized correctly. Insulated shutters or a sealed cover for the fan costs $50 to $150 and pays for itself in the first winter, because an uncovered fan leaks heated air into the attic all winter. Budget $1,000 to $1,500 for a basic installed fan in a 1,500 sq ft home, and $1,800 to $2,500 for a large, quiet, ducted fan with a timer and an insulated cover. Check the insulation around the fan with the Insulation Calculator, because a well-insulated attic makes the fan work better and the house cheaper to heat in winter.

Close-up of a whole-house fan motor and blades mounted in an attic above a ceiling opening, with insulation and ducting around it
A whole-house fan costs $1,000 to $2,500 installed, uses about 10 percent of the electricity of central air conditioning, and can cut cooling costs by 50 to 90 percent in climates with cool evenings.

How do you install a whole-house fan?

Installing a whole-house fan takes 4 to 8 hours for a professional and involves cutting a ceiling opening, framing it, mounting the fan, wiring it, and checking the attic ventilation, and the job should be done by an electrician for the wiring and a carpenter or handyman for the framing. Start by choosing the location: the fan should sit in a central hallway or landing on the top floor, where it can pull air from every room, and it needs at least 3 ft (0.9 m) of clear attic space above it. Mark the ceiling opening from below, check for joists, wiring, and plumbing with a stud finder and a small inspection hole, and cut the opening with a drywall saw. Frame the opening with 2 by 4 lumber, screwed to the ceiling joists, so the fan housing has a solid frame to sit in. Mount the fan in the frame, level it, and secure it with the screws or brackets that come with the unit, making sure the fan is square in the opening so the blades do not rub.

Wire the fan to a dedicated 15-amp circuit, or to an existing circuit that has capacity, and install the switch or timer on the wall near the fan, at a height of 48 to 52 in (122 to 132 cm) from the floor. A timer switch costs $30 to $60 and is worth it, because it lets the fan run for 1 to 2 hours and shut itself off, so you do not have to remember to turn it off before bed. A thermostat costs $50 to $100 and turns the fan on only when the indoor temperature is above the set point. Seal around the fan frame with caulk or foam, because any gap leaks heated air into the attic in winter and cooled air in summer. Install an insulated cover or shutter over the fan for winter, or buy a fan with built-in insulated dampers that close automatically when the fan is off. Test the fan by opening two or three windows, turning it on, and checking that air flows in through the windows and out through the attic vents, and that no doors slam shut. If the fan is loud, check that it is level, that the blades are tight, and that the attic has enough vent area, because a fan starved for exhaust air vibrates and hums.

How much can a whole-house fan save on cooling costs?

A whole-house fan can cut cooling costs by 50 to 90 percent in climates with cool evenings, and the savings depend on the climate, the insulation, and how often you run it instead of the air conditioner. In the Pacific Northwest, the Mountain West, and the Northeast, where summer evenings drop below 70 degrees Fahrenheit (21 degrees Celsius), a whole-house fan can replace air conditioning on most days and save $400 to $600 a year. In the Midwest and the Mid-Atlantic, where evenings are cooler but days are humid, a fan saves $200 to $400 a year by cooling the house in the evening and letting the air conditioner run less during the day. In the hot, humid South, where evenings stay above 75 degrees Fahrenheit (24 degrees Celsius), a fan saves $100 to $200 a year, because it still flushes the attic and cools the house on the cooler nights of spring and fall. In the dry Southwest, a fan works well on most summer evenings and saves $300 to $500 a year, because the dry air cools fast after sunset.

The savings come from three places: the fan uses 200 to 700 watts instead of the 3,000 to 5,000 watts of central air conditioning, the fan cools the house in 30 minutes instead of running all evening, and the fan flushes the attic, which drops the attic temperature by 20 to 40 degrees Fahrenheit (11 to 22 degrees Celsius) and cuts the heat that radiates into the living space. A home that runs the air conditioner 8 hours a day at 50 cents an hour spends $4 a day, or $360 a summer, while the same home running a whole-house fan for 2 hours a day at 3 cents an hour spends 6 cents a day, or $5 a summer. The fan does not dehumidify, so on humid days when the indoor humidity is above 60 percent, run the air conditioner instead, because a fan that pulls in humid air makes the house feel sticky. The best strategy is to run the fan in the evening and at night, and run the air conditioner only on the hottest, most humid afternoons, which cuts the cooling bill by half or more in most climates.

What are the most common whole-house fan mistakes?

The most common whole-house fan mistake is running it with the windows closed, because the fan then pulls air down the chimney, through the water heater flue, and through any gas appliance vent, which can pull carbon monoxide into the house. Always open at least two windows before you turn the fan on, and never run it in a home with a gas water heater or furnace unless those appliances are sealed-combustion or power-vented. The second mistake is too little attic ventilation: a fan that pushes 6,000 CFM into an attic with only 4 sq ft of vent area pressurizes the attic and pushes hot air back down through the ceiling, so check the vent area before you install and add vents if needed. The third mistake is the wrong size: a fan that is too small never cools the house, and a fan that is too large is loud and slams doors. Size the fan to 3 to 5 CFM per square foot of living space, and choose a two-speed model so you can run it quietly at night.

The fourth mistake is no winter cover: an uncovered whole-house fan leaks heated air into the attic all winter, which wastes $50 to $150 a year in heating and can cause ice dams on the roof. Cover the fan with an insulated cover from November to March, or buy a fan with built-in insulated dampers. The fifth mistake is installing the fan in the wrong place: a fan in a bedroom cools only that room, while a fan in a central hallway cools the whole house. The sixth mistake is running the fan on a humid evening, because it pulls in moist air that makes the house feel sticky and can grow mold in a damp attic. Check the outdoor humidity before you run the fan, and use the air conditioner when the humidity is above 60 percent. The seventh mistake is skipping maintenance: a fan that is never cleaned collects dust on the blades, which unbalances it and makes it loud, and a belt-drive fan with a worn belt slips and moves less air. Clean the blades and the grille every spring, oil the motor bearings if the manual calls for it, and replace a worn belt every 5 to 7 years. A fan that is sized right, vented right, and covered in winter lasts 15 to 25 years and pays for itself several times over.

Frequently asked questions

Keep reading

Attic Ventilation Guide: Soffit, Ridge and the Balance That Prevents Ice Dams

How-To

Vent an attic with balanced intake and exhaust — roughly 1 sq ft of ventilation per 150 sq ft of attic floor, split equally between soffit intake and ridge exhaust.

Read the article

Furnace Maintenance Guide: Filters, Safety Checks and a Fall Tune-Up That Prevents a Breakdown

How-To

A $15 filter changed on schedule, a flame that burns blue, and a fall tune-up before the first cold snap — most furnace breakdowns are preventable, and the ones that are not are caught early by the checks in this guide.

Read the article