Article — How-To · November 16, 2026 · 15 min read
How to Install Laminate Flooring: A Step-by-Step DIY Guide
Installing laminate flooring costs $3 to $8 per sq ft do-it-yourself and takes one weekend for a 200 sq ft room: buy 10 percent extra, acclimate the boxes for 48 hours, and keep a 1/4 to 3/8 inch expansion gap at every wall.
Installing laminate flooring costs $3 to $8 per sq ft ($32 to $86 per sq m) do-it-yourself, or $6 to $12 per sq ft ($65 to $129 per sq m) professionally installed, and a 200 sq ft (18.6 sq m) room takes one weekend for a first-time installer: Saturday to prep the subfloor and lay the first half, Sunday to finish, trim, and install the baseboards. Laminate is the most forgiving floor to install yourself because the planks click together with no glue, no nails, and no sanding, and a single box covers 15 to 30 sq ft (1.4 to 2.8 sq m). Measure the room first with the Square Footage Calculator, price the material with the Laminate Flooring Calculator, read the flooring installation cost guide to compare DIY against hiring out, and read the how to measure a room for flooring guide before you buy a single box.
How much laminate flooring do you need, and how much extra should you buy?
You need the room's square footage plus 10 percent extra for waste in a square room, and 15 percent extra for a room with angles, closets, or a diagonal layout. A 200 sq ft (18.6 sq m) square room needs 220 sq ft (20.4 sq m) of laminate, which is 8 to 15 boxes depending on the box size. A 300 sq ft (27.9 sq m) L-shaped room needs 345 sq ft (32.1 sq m), which is 12 to 23 boxes. The extra covers cut ends, damaged planks, and the last row, which is almost always ripped to a narrower width. Buy all the boxes from the same batch and dye lot, because two boxes of the same color from different production runs can differ visibly in shade. Keep one unopened box after the job for future repairs: a single damaged plank can be replaced from the spare box, and the same color may be discontinued within 2 to 3 years.
Acclimate the laminate before you install it. Stack the unopened boxes flat in the room for 48 to 72 hours at a temperature of 60 to 80 degrees Fahrenheit (16 to 27 degrees Celsius) and a humidity of 30 to 50 percent, so the planks adjust to the room's conditions. Installing cold planks straight from a garage in winter is the most common cause of gaps opening up in the first month: the planks expand as they warm, and a floor installed tight in January will buckle in July. Check the moisture of the subfloor before you start: a concrete subfloor must read below 4.5 percent moisture on a meter, and a wood subfloor must read below 12 percent. If the concrete is damp, lay a 6 mil (0.15 mm) plastic vapor barrier under the underlayment, overlapping the seams by 8 inches (20 cm) and taping them, or the laminate will swell and cup within a year.
What tools and materials do you need to install laminate flooring?
You need a tapping block, a pull bar, spacers, a utility knife, a jigsaw or circular saw, a tape measure, a chalk line, a level, and a rubber mallet, and the total tool cost is $80 to $150 if you buy them all new. The tapping block costs $10 to $15 and protects the plank edges when you tap them together; never hit a laminate plank directly with a hammer, because the click-lock edge chips and the joint will not lock. The pull bar costs $10 to $15 and hooks the last plank in each row tight against the previous one where the tapping block cannot reach. Spacers cost $5 to $10 for a pack and hold the 1/4 to 3/8 inch (6 to 10 mm) expansion gap around every wall. A jigsaw costs $40 to $80 and cuts curves around pipes and door jambs; a circular saw or miter saw cuts straight crosscuts faster, but a jigsaw is the one tool that handles every cut on the job.
Materials are the laminate itself, the underlayment, the vapor barrier if needed, and the trim. Underlayment costs $0.30 to $0.80 per sq ft ($3.20 to $8.60 per sq m) and does three jobs: it cushions the floor, it quiets footsteps, and it smooths minor subfloor bumps up to 1/8 inch (3 mm). Foam underlayment is the cheapest and works on wood subfloors; cork underlayment costs $0.60 to $1.00 per sq ft ($6.50 to $10.80 per sq m) and is the best sound absorber; a 3-in-1 underlayment with a built-in vapor barrier costs $0.50 to $0.90 per sq ft ($5.40 to $9.70 per sq m) and is the right choice over concrete. Transition strips cost $15 to $40 each and cover the joint where laminate meets tile, carpet, or another floor. Quarter-round or baseboard shoe molding costs $0.50 to $1.50 per linear foot ($1.60 to $4.90 per m) and covers the expansion gap at the walls. Rent a table saw for $40 to $60 a day if you have many long rip cuts, but a circular saw with a straightedge guide handles the same cuts for free.
How do you prepare the subfloor for laminate?
Prepare the subfloor by making it clean, dry, flat, and level: sweep and vacuum it, fix any squeaks, fill low spots, and sand down high spots until no point deviates more than 3/16 inch (5 mm) over 10 feet (3.0 m). Laminate is a floating floor, which means it is not attached to the subfloor, so it follows the shape of whatever is underneath: a hump of 1/4 inch (6 mm) will make the planks rock and the click locks will separate within months. Check flatness with a 10 foot (3.0 m) straightedge or a long level, and mark every high spot with a pencil. Sand down wood high spots with a belt sander, and fill wood low spots with a floor-leveling compound that costs $25 to $40 per bag and covers 50 sq ft (4.6 sq m) at 1/8 inch (3 mm) thick. On concrete, grind down high spots with a concrete grinder, which rents for $50 to $80 a day, and fill low spots with self-leveling compound at $30 to $50 per bag.
Fix squeaks before the laminate goes down, because you cannot reach the subfloor afterward. Walk the room slowly and mark every squeak with painter's tape, then drive 2 inch (5 cm) screws through the subfloor into the joists at each mark, or use a squeak-repair kit that costs $20 to $30 and breaks the screw head off below the surface. Remove the old baseboards with a pry bar and a putty knife, and number them on the back so they go back in the same place. Undercut the door jambs with a handsaw or an oscillating multi-tool so the laminate slides underneath: lay a scrap plank upside down next to the jamb, use it as a guide, and cut the jamb at that height. The laminate should slide 1/4 inch (6 mm) under the jamb, not butt against it, or the floor cannot expand and will buckle. Lay the underlayment in rows, tape the seams, and trim it flush at the walls before the first plank goes down.
How do you lay laminate flooring row by row?
Lay laminate flooring row by row from left to right, starting against the longest straight wall, with the tongue side facing the wall and a 1/4 to 3/8 inch (6 to 10 mm) spacer gap between the first row and the wall. Click the short ends together first: hold the plank at a 20 to 30 degree angle, insert the tongue into the groove of the previous plank, and lower it flat until it clicks. Tap the joint gently with the tapping block if it does not close fully, and check that the seam is tight with no visible gap. The first row is the most important row in the whole job: if it is not straight, every row after it will drift, so snap a chalk line 1/4 inch (6 mm) from the wall and check the row against it every 4 feet (1.2 m). If the starting wall is not straight, scribe the first row to the wall by tracing the wall's curve onto the planks and cutting along the line.
Stagger the end joints by at least 8 inches (20 cm) between rows, and never let two end joints line up within 8 inches (20 cm) of each other, because aligned joints weaken the floor and look like a mistake. Start the second row with the cutoff piece from the end of the first row, as long as it is at least 8 inches (20 cm) long, which saves material and staggers the joints naturally. Work across the room one row at a time, tapping each row tight against the previous row with the tapping block, and use the pull bar on the last plank in each row where the block cannot reach. The last row is almost always narrower than a full plank: measure the gap, subtract the 1/4 inch (6 mm) expansion gap, and rip the planks to that width on the circular saw. Install the last row with the pull bar, hooking it over the end of the plank and tapping it tight. A 200 sq ft (18.6 sq m) room takes 4 to 6 hours to lay once the subfloor is prepped, and a first-time installer should budget a full day.
How do you cut laminate around doorways, vents, and pipes?
Cut laminate around doorways, vents, and pipes by measuring twice, marking the cut on the back of the plank, and cutting with a jigsaw, because a jigsaw handles every shape on the job and a wrong cut wastes a plank. For a door jamb, undercut the jamb first so the laminate slides underneath, then measure the plank to the jamb and cut it to length. For a floor vent, measure the vent opening, mark it on the plank, drill a starter hole in each corner with a 3/8 inch (10 mm) drill bit, and cut the opening with the jigsaw. For a radiator pipe, measure the pipe center from the wall and from the end of the plank, drill a hole 1/2 inch (13 mm) larger than the pipe diameter, then cut a wedge from the hole to the edge of the plank so the plank slides around the pipe, and glue the wedge back in place behind the pipe where it is hidden by the escutcheon.
The trickiest cut is the first and last plank in a row that meets an angled wall or a closet opening. Measure the plank length at both ends of the cut, because an angled wall means the two ends are different lengths, and transfer both measurements to the plank before cutting. Cut laminate with the finished side down when using a circular saw, because the saw blade cuts upward and chips the top face, and cut with the finished side up when using a jigsaw, because the jigsaw blade cuts on the upstroke. A fine-tooth blade with 40 or more teeth gives a clean edge on both tools, and a dull blade chips the wear layer and leaves a ragged edge that shows in the joint. Keep a spare plank on hand for practice cuts, and cut the most visible planks last, after you have the feel of the saw and the material.
What are the most common laminate installation mistakes?
The most common laminate installation mistake is skipping the expansion gap: a floor installed tight against the walls has nowhere to expand in summer humidity, and it buckles in the middle of the room. Leave a 1/4 to 3/8 inch (6 to 10 mm) gap at every wall, every pipe, and every door jamb, and cover it with baseboard or quarter-round molding, never with caulk. The second mistake is installing over a subfloor that is not flat: a hump of 1/4 inch (6 mm) makes the planks rock, the click locks separate, and the floor squeaks with every step. The third mistake is not staggering the end joints: joints closer than 8 inches (20 cm) apart create a weak line across the floor and look unprofessional. The fourth mistake is installing the laminate in the wrong direction: run the planks parallel to the longest wall and parallel to the main light source, usually the largest window, so the seams disappear in the light instead of casting shadows.
The fifth mistake is forgetting the transition strips: a floating floor must be able to expand, so any run longer than 30 feet (9.1 m) or any doorway between two rooms needs a transition strip, or the floor will buckle at the weakest point. The sixth mistake is using the wrong underlayment over concrete: without a vapor barrier, moisture rises through the slab and swells the laminate from below, and the damage shows up as cupped edges within 6 to 12 months. If you are comparing laminate with refinishing the floor you already have, read the hardwood floor refinishing guide before you decide, because a solid hardwood floor that can be sanded and refinished for $3 to $5 per sq ft ($32 to $54 per sq m) is often a better investment than covering it with laminate. A laminate floor installed right lasts 15 to 25 years, and the most common repair is replacing a single damaged plank from the spare box you kept.
Frequently asked questions
A 200 sq ft room takes one weekend for a first-time installer: Saturday to prep the subfloor and lay the first half, Sunday to finish, trim, and install the baseboards. An experienced installer lays 200 sq ft in 4 to 6 hours once the subfloor is prepped. A 500 sq ft area takes 2 to 3 days for a DIY installer, including subfloor prep and trim. Add a day if the subfloor needs leveling or if you are removing old flooring first.
Yes, you can install laminate over vinyl, linoleum, tile, and wood, as long as the old floor is flat, clean, dry, and firmly attached, with no point deviating more than 3/16 inch over 10 feet. You cannot install laminate over carpet, carpet pad, or a floating floor, because the soft base lets the planks move and the click locks separate. Over tile, use a thick underlayment to bridge the grout lines. Over concrete, use an underlayment with a built-in vapor barrier.
Installing laminate flooring yourself costs $3 to $8 per sq ft, including the laminate at $1.50 to $5 per sq ft, underlayment at $0.30 to $0.80 per sq ft, and trim and transitions at $0.50 to $1.50 per linear foot. A 200 sq ft room costs $600 to $1,600 in materials plus $80 to $150 in tools if you buy them new. Professional installation costs $6 to $12 per sq ft, so a 200 sq ft room costs $1,200 to $2,400 hired out. DIY saves $600 to $1,000 on a typical room.
Yes, laminate flooring needs underlayment in almost every installation. Underlayment cushions the floor, quiets footsteps, smooths minor subfloor bumps up to 1/8 inch, and, over concrete, blocks moisture with a built-in vapor barrier. Foam underlayment costs $0.30 to $0.50 per sq ft and works on wood subfloors. A 3-in-1 underlayment with a vapor barrier costs $0.50 to $0.90 per sq ft and is required over concrete. Some laminate comes with pre-attached underlayment, in which case you do not add a second layer.
The expansion gap for laminate flooring is 1/4 to 3/8 inch at every wall, pipe, door jamb, and fixed object. Laminate expands and contracts with temperature and humidity, and without the gap the floor buckles in the middle of the room in summer. The gap is covered by baseboard or quarter-round molding, never by caulk. Any run longer than 30 feet or any doorway between two rooms needs a transition strip so the floor can expand in sections.
Keep reading
Hardwood Floor Refinishing: Sanding, Staining and Cost per Square Foot
How-ToA floor is refinishing-ready when solid wood still has sandable thickness above the tongue — a recoat at $1 to $2.50 per sq ft handles a dull finish, while full refinishing at $3 to $8 per sq ft fixes wear through to bare wood.
Read the articleHow to Measure a Room for Flooring (So You Never Run Short)
How-ToMeasure the room as a set of rectangles, account for closets and angled walls, then add waste for the layout you will actually install. A step-by-step method that turns a tape measure into a reliable box count.
Read the article