Article — How-To · November 13, 2026 · 15 min read
Hardwood Floor Installation Cost: Materials, Labor and What a 1,000 Sq Ft Job Runs
Hardwood floor installation costs $8 to $15 per sq ft for solid wood and $6 to $14 for engineered wood, so a 1,000 sq ft job runs $8,000 to $15,000 for solid and $6,000 to $14,000 for engineered, with the species, the subfloor, and the finish deciding the final number.
Hardwood floor installation costs $8 to $15 per sq ft installed for solid hardwood and $6 to $14 per sq ft for engineered hardwood, so a 1,000 sq ft job runs $8,000 to $15,000 for solid wood and $6,000 to $14,000 for engineered wood, including materials, labor, and underlayment. The species you choose moves the price more than anything else: red oak runs $5 to $8 per sq ft for materials, white oak runs $6 to $10, and walnut runs $8 to $14. Labor adds $4 to $8 per sq ft, and removing old flooring, leveling the subfloor, and finishing add $1 to $5 per sq ft more. Price your job with the Hardwood Flooring Calculator, compare the full installed price in the flooring installation cost guide, and plan the measuring step with the how to measure a room for flooring guide and the hardwood floor refinishing guide.
How much does hardwood floor installation cost?
Hardwood floor installation costs $8 to $15 per sq ft installed for solid hardwood and $6 to $14 per sq ft for engineered hardwood, and a typical 1,000 sq ft job runs $8,000 to $15,000 for solid wood or $6,000 to $14,000 for engineered wood. Materials are the biggest share of the bill: solid hardwood planks cost $5 to $10 per sq ft, engineered planks cost $4 to $9 per sq ft, and underlayment, adhesive or fasteners, and trim add $1 to $2 per sq ft. Labor costs $4 to $8 per sq ft for a standard nail-down or glue-down installation, and the rate climbs toward the top of that range for herringbone or diagonal patterns, for stairs, and for rooms with a lot of closets and doorways. Removing old carpet or vinyl costs $1 to $2 per sq ft, removing old hardwood or tile costs $2 to $4 per sq ft, and leveling a subfloor costs $1 to $3 per sq ft where the floor is out of flat.
The total for a whole house follows the same math. A 500 sq ft bedroom level in red oak costs $4,000 to $7,500 installed, a 1,000 sq ft main floor in white oak costs $8,000 to $15,000, and a 2,000 sq ft full-home installation in hickory or walnut costs $18,000 to $30,000. Site-finished floors add $3 to $5 per sq ft for sanding, staining, and three coats of finish, and the finish needs 24 to 72 hours to cure before furniture goes back. Prefinished floors cost more per plank but need no sanding and no cure time, so you can walk on them the same day. Get three written quotes that break out materials, labor, removal, and finishing separately, because a single lump-sum quote hides the places where one installer is charging double for removal or underlayment. A quote that is far below the rest usually leaves out the moisture barrier, the transitions, or the shoe molding, and those items show up as extras later.
Which hardwood species and grade should you choose?
Red oak is the best hardwood species for most homeowners, because it costs $5 to $8 per sq ft for materials, takes stain evenly, hides dents better than softer woods, and matches the trim and cabinets in most American homes. Red oak scores 1,290 on the Janka hardness scale, which measures how much force it takes to dent the wood, and that hardness is enough for living rooms, bedrooms, and hallways with normal foot traffic. White oak costs $6 to $10 per sq ft, scores 1,360 on the Janka scale, resists water better than red oak because its pores are closed, and suits kitchens and entryways where spills and wet shoes are common. Maple costs $6 to $9 per sq ft and scores 1,450, which makes it one of the hardest domestic woods, but its pale, even grain shows every scratch, so it suits bedrooms and low-traffic rooms better than a busy family room.
Hickory costs $6 to $10 per sq ft, scores 1,820 on the Janka scale, and is the hardest common domestic hardwood, which makes it the right choice for a home with large dogs or heavy furniture. Its strong color variation from cream to brown hides dirt and scratches well, but the same variation makes it hard to match from box to box, so order 10 to 15 percent extra and mix planks from several boxes as you install. Walnut costs $8 to $14 per sq ft and scores only 1,010, so it dents more easily, but its rich dark brown color is the reason people choose it for formal living rooms and dining rooms. Exotic species such as Brazilian cherry and teak cost $10 to $18 per sq ft and score 2,000 or higher, but they darken with sunlight and can be hard to refinish. Grade matters as much as species: select grade is the most uniform and costs the most, common grade has more knots and color variation and costs 20 to 30 percent less, and rustic grade is the cheapest but suits only a cabin or farmhouse look. For a family home, choose a mid-grade white oak or hickory in a 3 to 5 in wide plank, which balances cost, durability, and a current look.
Solid hardwood or engineered hardwood: which is better for your home?
Engineered hardwood is the better choice for most homes built on a concrete slab, for kitchens, and for any room below grade, because its layered plywood core resists moisture and temperature swings that make solid hardwood cup, gap, and buckle. Engineered planks cost $4 to $9 per sq ft for materials and $6 to $14 per sq ft installed, and a quality engineered plank has a 3 to 6 mm wear layer of real hardwood over a plywood base, which means it can be refinished one or two times. Solid hardwood costs $5 to $10 per sq ft for materials and $8 to $15 per sq ft installed, and a 3/4 in solid plank can be refinished 5 to 10 times over a 100-year life, which is why it still wins for a long-term home where the floors are an investment. The wear layer is the number that matters: a 2 mm wear layer cannot be sanded at all, a 3 mm wear layer allows one light sanding, and a 4 mm or thicker wear layer allows two or more full refinishes.
Choose solid hardwood for a second floor or any room over a wood subfloor in a climate-controlled home, and choose engineered hardwood for a ground floor on a concrete slab, a basement, or a home with radiant floor heat. Solid hardwood cannot go directly on concrete because nails have nothing to grip and moisture wicks up from the slab, while engineered hardwood can be glued down or floated over a moisture barrier. Radiant heat limits solid wood to narrow planks under 3 in wide, because wide solid planks move too much with the heat cycles, while engineered planks handle radiant heat well at any width. If you plan to stay in the home for decades and want floors that outlast you, buy solid oak or hickory. If you need a floor that handles a slab, a basement, or a kitchen, buy engineered wood with a wear layer of at least 4 mm and a plywood core, not a fiberboard core. Avoid engineered planks with a wear layer under 2 mm: they look like hardwood, but they cannot be refinished, and a deep scratch means replacing the plank, not sanding it.
How do you prepare a subfloor for hardwood installation?
Preparing a subfloor for hardwood takes half a day for a typical room and decides whether the floor stays flat and quiet or squeaks and cups within a year. Start by testing moisture: a wood subfloor should read 6 to 9 percent moisture, and the hardwood planks should be within 2 percent of the subfloor reading, so a subfloor at 8 percent and planks at 7 percent are a good match. A concrete slab should read under 3 lbs of moisture per 1,000 sq ft per 24 hours on a calcium chloride test, or under 75 percent relative humidity on an in-slab probe, and any slab that reads higher needs a moisture barrier or a sealant before installation. Acclimate the planks in the room where they will be installed for 3 to 7 days, stacked with 1 in spacers between the layers so air reaches every plank, with the heat running at the normal living temperature of 60 to 80 degrees Fahrenheit and the humidity between 30 and 50 percent.
Check the subfloor for flatness with a 6 ft level or a straightedge: the floor must be flat within 3/16 in over 10 ft for hardwood, and any high spot gets sanded down while any low spot gets filled with a floor-leveling compound. Screw down any loose subfloor panels with 2 in screws every 6 in along the joists, because a squeak that exists before the hardwood goes down will still be there after, and it is 10 times harder to fix then. Sweep and vacuum the subfloor until no dust, grit, or staples remain, because a single staple under a plank creates a bump that telegraphs through the floor. Lay a 15 lb felt paper or a synthetic underlayment over a wood subfloor, overlapping the seams by 4 in, and lay a 6 mil polyethylene moisture barrier over concrete, overlapping the seams by 6 in and running it 2 in up the walls. Never install hardwood over a damp subfloor, a subfloor with a moisture reading more than 2 percent away from the planks, or a floor that is not flat: the installer who skips these checks is the installer whose floors cup in the first humid summer.
What does the installation process look like step by step?
A nail-down hardwood installation takes 1 to 3 days for 1,000 sq ft, and the steps are: acclimate, lay out, install the first rows, nail the field, and finish the edges. The installer starts by laying out the planks along the longest wall, snapping a chalk line 3/4 in from the wall for the expansion gap, and dry-fitting the first three rows to check the color mix and to make sure the last row will not be a sliver less than 2 in wide. If the last row would be too narrow, the installer rips the first row narrower so the first and last rows end up close to the same width. The first row is face-nailed through the top of the plank near the wall, where the baseboard will cover the nails, and the second and third rows are nailed through the tongue at a 45-degree angle with a pneumatic flooring nailer. The rest of the field is nailed every 6 to 8 in along each plank, with the end joints staggered at least 6 in from the joints in the neighboring rows, and planks are pulled from three or four boxes at once so the color variation spreads evenly across the floor.
Glue-down installation suits engineered wood on concrete: the installer spreads adhesive with a notched trowel, sets each plank, and rolls the floor with a 100 lb roller to press the planks into the glue. Floating installation suits engineered wood as well: the planks click together with no nails and no glue, the whole floor floats over the underlayment, and the job goes faster, but a floating floor can sound hollow underfoot and cannot be refinished in place. Around doorways, the installer undercuts the door jambs with a jamb saw so the planks slide underneath, which looks far better than cutting the planks around the trim. At the edges, the installer leaves a 3/4 in expansion gap on every wall, covers it with baseboard and shoe molding, and installs T-molding transitions where the hardwood meets tile or carpet. The crew should leave you with one full box of extra planks, about 5 to 10 percent of the order, for future repairs. A floor that is installed without the expansion gap will buckle in the first humid summer, and a floor installed with end joints lined up in a stair-step pattern will look amateur for the life of the floor.
How long does hardwood floor installation take and when can you walk on it?
Hardwood floor installation takes 1 to 3 days for 1,000 sq ft of prefinished flooring and 4 to 7 days for the same area site-finished, and you can walk on a prefinished floor the same day the crew finishes. A 500 sq ft bedroom takes 1 day, a 1,000 sq ft main floor takes 2 to 3 days, and a 2,000 sq ft whole-house job takes 4 to 6 days, with an extra day for stairs and an extra day if old flooring has to come out first. Site-finished floors add 3 to 4 days: one day to sand, one day to stain, and one to two days for two or three coats of polyurethane, with 8 to 12 hours of drying between coats. You can walk on a site-finished floor in socks after 24 hours, move light furniture back after 72 hours, and put rugs down after 7 days, because the finish is still curing and a rug traps the solvents underneath and leaves a mark.
Plan the schedule around the cure time, not the installation time. Move furniture out of every room before the crew arrives, because a crew that has to move furniture charges $100 to $300 extra and works slower. Keep pets and children out of the work area, and keep the heat between 60 and 80 degrees Fahrenheit and the humidity between 30 and 50 percent for the first week, because the wood is still settling into the home. Do not mop a new floor for at least 7 days, and when you do, use a damp mop, never a wet mop or a steam mop, because standing water is the fastest way to damage a new hardwood floor. A prefinished floor is the right choice when you need the rooms back fast, such as a rental turnover or a move-in deadline. A site-finished floor is the right choice when you want a perfectly flat finish with no bevels between planks, or when you are matching an existing floor in the next room. Either way, ask the installer for the exact walk-on time in writing before the job starts, so a family gathering or a move-in date does not collide with a curing floor.
How do you maintain hardwood floors after installation?
Maintain hardwood floors with a weekly dry mop or vacuum and a damp mop once a month, and a well-kept floor lasts 50 to 100 years. Sweep or vacuum with a hard-floor setting every week, because grit is sandpaper: a single grain of sand under a shoe scratches the finish, and a thousand grains over a year dull the whole floor. Damp-mop once a month with a cleaner made for hardwood, wringing the mop until it is barely damp, and never use a steam mop, a wet mop, or a vinegar-and-water mix, because steam forces moisture into the seams and vinegar dulls polyurethane over time. Put felt pads under every chair and table leg, and replace them every 6 months, because a worn pad is worse than no pad: the grit embeds in the felt and grinds the finish. Put a doormat at every exterior door and a rug in front of the kitchen sink and the dishwasher, which are the two places where water hits the floor most often.
Keep the indoor humidity between 30 and 50 percent year-round with a humidifier in winter and a dehumidifier or air conditioning in summer, because wood shrinks in dry air and swells in humid air, and the gaps that open in January close in July only if the humidity stays in range. Recoat the finish every 5 to 7 years in high-traffic areas, which costs $1 to $2 per sq ft and takes a day, and the recoat is a light sanding and a fresh coat of polyurethane, not a full sanding. Refinish the floor every 15 to 25 years, which costs $3 to $5 per sq ft and removes the top layer of wood along with the old finish. A floor that is cleaned weekly, kept dry, and recoated on schedule looks new for decades. A floor that is mopped wet, left humid in summer and bone dry in winter, and never recoated will need a full refinish in 10 years and a replacement in 30. The maintenance costs about $100 a year in pads, cleaner, and mats, which is the cheapest insurance a floor ever gets.
Common hardwood installation mistakes and how to avoid them
The most common hardwood installation mistake is skipping acclimation: planks installed straight from the truck at 12 percent moisture shrink to 7 percent in a heated home, and the floor opens up with 1/8 in gaps between every plank within a month. The second mistake is installing over a damp subfloor: a concrete slab that was not moisture-tested cups the planks from below, and the floor has to come up to fix it. The third mistake is no expansion gap: a floor installed tight to the wall has nowhere to go when summer humidity swells the wood, and the middle of the floor buckles upward. The fourth mistake is lining up the end joints in a regular pattern, which looks like a brick wall and marks the job as amateur: stagger every end joint at least 6 in from its neighbors. The fifth mistake is nailing too close to the ends of the planks, which splits the tongue and leaves a loose plank that squeaks.
The sixth mistake is choosing the wrong wood for the room: solid hardwood in a basement or on a slab will cup, and a soft species such as pine or walnut in a hallway with dogs will dent within a year. The seventh mistake is ordering too little material: order 10 percent extra for a straight installation and 15 percent for a diagonal or herringbone pattern, because a short order stops the job while you wait a week for a matching batch. The eighth mistake is hiring the cheapest installer without checking references: a bad installation costs $8 to $15 per sq ft to tear out and redo, which is more than the original job. Avoid all of these by checking moisture readings yourself, watching the crew leave the expansion gap, mixing planks from several boxes, and keeping one full box of extra planks after the job. A floor installed correctly is a 100-year floor; a floor installed wrong is a 3-year floor.
Frequently asked questions
Hardwood floor installation costs $8 to $15 per sq ft installed for solid hardwood and $6 to $14 per sq ft for engineered hardwood. Materials cost $5 to $10 per sq ft for solid wood and $4 to $9 per sq ft for engineered wood, labor costs $4 to $8 per sq ft, and underlayment and trim add $1 to $2 per sq ft. Removing old flooring adds $1 to $4 per sq ft, leveling the subfloor adds $1 to $3 per sq ft, and site finishing adds $3 to $5 per sq ft. Red oak is the cheapest quality option at $5 to $8 per sq ft for materials, while walnut runs $8 to $14 and exotics run $10 to $18.
Installing hardwood floors in 1,000 sq ft costs $8,000 to $15,000 for solid hardwood and $6,000 to $14,000 for engineered hardwood, including materials, labor, and underlayment. A 1,000 sq ft job in red oak runs about $8,000 to $11,000, the same area in white oak runs $9,000 to $13,000, and walnut runs $11,000 to $15,000. Removing old flooring adds $1,000 to $4,000, and site finishing adds $3,000 to $5,000. The job takes 1 to 3 days for prefinished flooring or 4 to 7 days for site-finished flooring, and you can walk on a prefinished floor the same day.
Solid hardwood is better for a long-term home with a wood subfloor, because a 3/4 in solid plank can be refinished 5 to 10 times and lasts 100 years. Engineered hardwood is better for a concrete slab, a basement, a kitchen, or a home with radiant floor heat, because its plywood core resists moisture and temperature swings that make solid wood cup and gap. Buy engineered wood with a wear layer of at least 4 mm so it can be refinished twice, and avoid wear layers under 2 mm, which cannot be sanded at all. Both types look the same once installed, and the right choice depends on the subfloor and the room, not on the appearance.
Yes, engineered hardwood can be installed over concrete by gluing it down or floating it over a moisture barrier, but solid hardwood should not go directly on concrete because nails have nothing to grip and moisture wicks up from the slab. Test the slab first: it should read under 3 lbs of moisture per 1,000 sq ft per 24 hours, or under 75 percent relative humidity. Lay a 6 mil polyethylene moisture barrier with seams overlapped by 6 in, and run it 2 in up the walls. For solid wood over concrete, the installer must first lay a plywood subfloor, which adds $2 to $3 per sq ft to the job.
Hire a professional for most hardwood installations, because a pro brings a pneumatic flooring nailer, a jamb saw, and the experience to keep the first course level, stagger the joints, and leave the expansion gap. A do-it-yourself installation saves the $4 to $8 per sq ft labor cost, or $4,000 to $8,000 on a 1,000 sq ft job, but it needs a rented nailer at $50 to $75 a day, a miter saw, and 2 to 4 days of work. A floating engineered floor is the most realistic do-it-yourself option. A nail-down solid floor, a glue-down floor, stairs, or a herringbone pattern should go to a pro, because a bad installation costs $8 to $15 per sq ft to tear out and redo.
Keep reading
Hardwood Floor Refinishing: Sanding, Staining and Cost per Square Foot
How-ToA floor is refinishing-ready when solid wood still has sandable thickness above the tongue — a recoat at $1 to $2.50 per sq ft handles a dull finish, while full refinishing at $3 to $8 per sq ft fixes wear through to bare wood.
Read the articleHow to Measure a Room for Flooring (So You Never Run Short)
How-ToMeasure the room as a set of rectangles, account for closets and angled walls, then add waste for the layout you will actually install. A step-by-step method that turns a tape measure into a reliable box count.
Read the article