Article — How-To · November 17, 2026 · 15 min read

How to Fix a Leaky Faucet: Diagnose the Drip and Repair It in an Afternoon

A leaky faucet wastes 3,000 to 5,000 gallons of water a year from a single drip per second, and fixing it costs $10 to $30 in parts and takes 30 to 90 minutes, while a plumber charges $150 to $350 for the same job.

A leaky faucet wastes 3,000 to 5,000 gallons of water a year from a single drip per second, and fixing it costs $10 to $30 in parts and takes 30 to 90 minutes, while a plumber charges $150 to $350 for the same job. The repair is almost always a worn washer, O-ring, or cartridge, and the fix depends on the faucet type: compression faucets need a new rubber washer, ball faucets need new springs and seats, cartridge faucets need a new cartridge, and ceramic disc faucets need new seals. Identify your faucet type first, buy the matching repair kit for $10 to $25, and you can stop the drip in one afternoon. If the faucet is over 15 years old or the finish is worn, compare the repair cost with a new one in the kitchen faucet buying guide and the bathroom faucet and showerhead buying guide, and check the sink it sits in with the kitchen sink buying guide.

Hands repairing a leaking kitchen faucet with pliers, with the handle removed and replacement washers and tools laid out on the counter

Why is my faucet leaking and how do I find the cause?

A faucet leaks because a seal inside it has worn out, and the most common cause is a rubber washer, O-ring, or cartridge seal that has hardened, cracked, or worn flat after years of use. A drip from the spout means the seal that shuts off the water is worn, which is a washer in a compression faucet, a spring and seat in a ball faucet, or a cartridge in a cartridge or ceramic disc faucet. A leak around the base of the faucet means the O-rings around the spout or the body have worn, and a leak around the handle means the packing nut is loose or the O-ring under the handle has failed. A drip of one drop per second wastes about 3,000 gallons a year, which adds $20 to $60 a year to a water bill in most US cities, and a steady stream wastes far more. Before you take anything apart, shut off the water at the valves under the sink, plug the drain so small parts cannot fall in, and take a photo of the faucet from the front and the side so you can identify the brand and model.

Identify the faucet type by looking at the handles. A compression faucet has two separate handles that you turn several times to open and close, and it is the oldest type, common in homes built before 1990. A ball faucet has a single handle that moves in a ball joint over a rounded cap, and it was the standard single-handle faucet for decades. A cartridge faucet has a single handle that moves up and down and side to side, and it is the most common type in homes built after 2000. A ceramic disc faucet also has a single handle, but it moves only a quarter turn from off to full on, and it is the most reliable type, often lasting 20 years or more. If you are not sure which type you have, take a photo to a hardware store, or remove the handle and look at the mechanism: a compression faucet has a stem with a rubber washer at the bottom, a ball faucet has a slotted metal ball, a cartridge faucet has a plastic or brass cylinder, and a ceramic disc faucet has two flat ceramic discs. Buy the repair kit that matches your brand and model, because a generic kit often fits poorly and leaks again within weeks.

How do you fix a compression faucet that drips?

A compression faucet that drips from the spout needs a new rubber washer, which costs $1 to $5 and takes 30 minutes to replace, and the washer sits at the bottom of the valve stem under a brass screw. Shut off the water at the valves under the sink, open the faucet to drain the remaining water, and remove the handle: look for a small screw on the side or under a decorative cap on top, and pry the cap off with a flat screwdriver if there is one. Unscrew the packing nut with an adjustable wrench, then unscrew the valve stem by turning it counterclockwise, the same way you would open the faucet, until it comes out. At the bottom of the stem you will see a rubber washer held on by a small brass screw: remove the screw, take off the old washer, and match it exactly at the hardware store, because washers come in dozens of sizes and a washer that is 1/16 in too large will not seat and a washer that is too small will leak.

While the stem is out, check the valve seat inside the faucet body, which is the brass ring the washer presses against. Run your fingertip around it: if it feels rough or pitted, the new washer will wear out again in weeks, and you need to smooth it with a valve-seat wrench, which costs $10 to $15, or replace the seat if it unscrews. Coat the new washer with a thin layer of plumber's silicone grease, which costs $3 to $5 a tube, screw it onto the stem, and reassemble in reverse order, tightening the packing nut until it is snug but not crushed. Turn the water back on slowly and check for drips: if the spout still drips, the washer is the wrong size or the seat is too worn, and if water leaks around the handle, tighten the packing nut a quarter turn at a time until it stops. Replace both the hot and cold washers at the same time, because if one is worn, the other is close behind, and a second repair in a month costs the same time again. A compression faucet that still leaks after a new washer and a dressed seat is usually worn beyond repair, and a new faucet costs $50 to $200.

How do you fix a ball faucet that leaks?

A ball faucet that drips from the spout needs new springs and seats, which cost $5 to $15 in a repair kit and take 45 minutes to replace, and the springs and rubber seats sit in the faucet body under the metal ball. Shut off the water, plug the drain, and loosen the set screw on the handle with a 1/8 in hex key, which is usually hidden under a small cap on the side of the handle. Lift the handle off, unscrew the cap with an adjustable wrench or channel-lock pliers, and lift out the cam, the cam washer, and the metal ball. Under the ball you will see two small rubber seats with springs underneath them, one for hot and one for cold: pull them out with needle-nose pliers or a small screwdriver, and note which side is hot and which is cold so the new ones go back in the same places. The springs lose tension over time and the seats harden and crack, which lets water past the ball and out of the spout even when the handle is off.

Buy a repair kit that matches your faucet brand, because the ball, cam, seats, and springs are sized to the model, and a kit costs $10 to $25 and includes everything. Install the new springs and seats first, pushing each spring into the hole with the narrow end down and the seat on top of it, then set the ball back in place, lining up the slot on the ball with the pin inside the faucet body. Set the cam and cam washer on top, screw the cap back on, and tighten it until it is snug, then slide the handle on and tighten the set screw. Turn the water on and test the handle through its full range: if it feels stiff, the cap is too tight, so back it off a quarter turn; if it drips, the cap is too loose, so tighten it a quarter turn. If the ball itself is scratched or corroded, replace it too, because a new seat cannot seal against a damaged ball, and a replacement ball costs $5 to $10. Ball faucets have more moving parts than other types and tend to leak more often, which is why many plumbers recommend replacing a ball faucet with a cartridge faucet when it needs a second repair, rather than fixing it again.

Close-up of a faucet valve stem with a worn rubber washer being replaced, showing the brass screw and the new washer beside it
A leaky faucet wastes 3,000 to 5,000 gallons of water a year from a single drip per second, and fixing it costs $10 to $30 in parts and takes 30 to 90 minutes, while a plumber charges $150 to $350 for the same job.

How do you fix a cartridge faucet that leaks?

A cartridge faucet that drips from the spout needs a new cartridge, which costs $15 to $40 and takes 30 to 45 minutes to replace, and the cartridge is a cylinder that controls both the flow and the temperature. Shut off the water, plug the drain, and remove the handle: look for a set screw under a cap on the side of the handle, or a screw on top under a decorative button. Pull the handle off, unscrew the retaining nut with an adjustable wrench, and pull the cartridge straight up and out of the faucet body. Note the orientation of the cartridge before you remove it, because it must go back in the same way, and take a photo of the top and the side so you can match it at the store. Cartridges are brand-specific and model-specific, so bring the old one with you or look up the faucet model number, which is often printed on a tag under the sink or on the box the faucet came in.

Before you install the new cartridge, flush the faucet body by turning the water on for 5 seconds with the cartridge out, which clears out grit and mineral deposits that would damage the new seals. Coat the O-rings on the new cartridge with plumber's silicone grease, slide it in the same orientation as the old one, and tighten the retaining nut until it is snug. Reattach the handle and test: turn the water on, run the faucet through hot and cold, and check for drips with the handle off and for leaks around the base. If the handle feels stiff, the retaining nut is too tight, so back it off a quarter turn. If the faucet still drips, the cartridge is the wrong model or the faucet body has mineral buildup, which you can clean by soaking the body in white vinegar for 30 minutes. A cartridge lasts 5 to 10 years in most homes, and 15 to 20 years in homes with soft water, because hard water minerals wear the seals faster. If your home has hard water, consider a water softener, because it extends the life of every faucet and appliance in the house.

How do you fix a ceramic disc faucet that leaks?

A ceramic disc faucet that drips from the spout needs new seals, which cost $5 to $15 and take 30 minutes to replace, and the seals sit under the ceramic disc cylinder inside the faucet body. Shut off the water, plug the drain, and remove the handle by loosening the set screw, then unscrew the decorative cap and the retaining nut to expose the ceramic disc cylinder. Lift the cylinder out and look underneath it: you will see two or three small rubber seals, which are usually black neoprene, sitting in the bottom of the faucet body. The seals harden and flatten over time, which lets water past the discs even when the handle is off. Pull the old seals out with a small screwdriver, clean the seat area with a cloth, and press the new seals into place, making sure they sit flat and the holes line up with the water ports.

Check the ceramic discs themselves while the cylinder is out: they should be smooth and free of chips, scratches, and mineral buildup. If a disc is chipped or cracked, the whole cylinder must be replaced, which costs $20 to $50 and is brand-specific, so bring the old cylinder to the store. Clean mineral deposits off the discs with white vinegar and a soft cloth, never with a wire brush or sandpaper, because a scratched ceramic disc will never seal again. Reassemble in reverse order, tighten the retaining nut until it is snug, and test the faucet: a ceramic disc faucet should turn only a quarter turn from off to full on, and it should shut off with no drip at all. Ceramic disc faucets are the most reliable type and rarely leak before 15 to 20 years, and when they do, the seals are almost always the cause. If a ceramic disc faucet leaks around the base, the O-rings around the spout need replacing, which takes the same 30 minutes and costs $3 to $8 for a set of O-rings matched to your model.

When should you replace a faucet instead of repairing it?

Replace a faucet instead of repairing it when the repair costs more than half the price of a new faucet, when the faucet is over 15 years old, or when the body is corroded, pitted, or cracked. A new kitchen faucet costs $50 to $300, a new bathroom faucet costs $40 to $200, and a plumber charges $150 to $350 to install one, so a repair that needs a $40 cartridge plus a $150 service call is already close to the price of a new faucet installed by a do-it-yourselfer. Replace the faucet when the finish is worn, peeling, or stained, because no repair fixes the appearance, and when the spout is corroded inside, because mineral buildup and corrosion narrow the waterway and cut the flow rate. Replace it when the faucet has already been repaired twice, because a third repair means the body itself is worn and the seals will not hold. Replace it when you cannot find parts, which happens with off-brand faucets and faucets over 20 years old, because a repair kit that does not fit exactly will leak again within weeks.

A new faucet is also the right choice when you want a feature the old one does not have: a pull-down sprayer, a touchless sensor, a higher arc for filling pots, or a water-saving aerator that cuts flow from 2.2 gallons per minute to 1.5 gallons per minute (8.3 to 5.7 liters per minute) and saves 700 gallons a year per faucet. Compare the options in the kitchen faucet buying guide and the bathroom faucet and showerhead buying guide, and match the new faucet to the sink, because a faucet with the wrong hole pattern will not fit: check whether your sink has one, two, three, or four holes before you buy, and look at the kitchen sink buying guide if the sink needs replacing too. A do-it-yourself faucet replacement takes 1 to 2 hours, needs a basin wrench for the nuts under the sink, and costs nothing in labor. A faucet that is repaired correctly should not drip again for 5 to 10 years, and a faucet that is replaced should last 15 to 20 years, so either way, a drip that you fix today is money back in your pocket by the end of the year.

Frequently asked questions

Keep reading

Kitchen Faucet Buying Guide: Types, Finishes and What a Good One Costs

Tips & Tricks

A good kitchen faucet costs $150 to $400 and lasts 15 to 20 years when you match the hole count, a spout reach of 8 to 9 in, and a flow rate of 1.5 to 1.8 gallons per minute; chrome and brushed nickel are the finishes that hold up longest, and a ceramic disc cartridge is the part that decides longevity.

Read the article

Bathroom Faucet and Showerhead Buying Guide: Flow Rates, Finishes and Water Savings

How-To

A good bathroom faucet costs $80 to $250 and a good showerhead costs $40 to $150; a WaterSense showerhead at 2.0 gallons per minute saves a family of four about 2,900 gallons of water a year, and the faucet must match the sink holes — 4 in centerset or 8 in widespread — with the spout clearing the basin rim by at least 4 in.

Read the article