Article — How-To · November 11, 2026 · 15 min read

Fence Staining and Sealing Guide: When, How Often and What It Costs

Staining a fence costs $700 to $2,000 professionally, or $150 to $400 do-it-yourself: wait 4 to 6 weeks after installing pressure-treated wood, stain below 15 percent moisture, and reapply a semi-transparent stain every 3 to 5 years.

Staining a fence costs $700 to $2,000 professionally, or $150 to $400 do-it-yourself, and the timing matters more than the product: wait 4 to 6 weeks after installing a new pressure-treated fence, stain when the wood moisture content is below 15 percent, and work in temperatures between 50 and 90 degrees Fahrenheit (10 to 32 degrees Celsius). A transparent stain needs reapplying every 2 to 3 years, a semi-transparent stain lasts 3 to 5 years, and a solid stain lasts 5 to 7 years. Size the project with the Fence Calculator, price the full fence with the fence installation cost guide, and keep the fence standing straight with the wood fence maintenance guide.

Homeowner staining a wooden backyard fence with a brush and a pump sprayer, with drop cloths protecting the grass below

When should you stain or seal a new fence?

Wait 4 to 6 weeks after installing a new pressure-treated wood fence before you stain it, and wait 3 to 6 months after installing a new cedar or redwood fence, because fresh lumber is too wet to absorb stain. Pressure-treated pine leaves the mill saturated with preservative, and the moisture content is often 30 percent or higher — stain applied to wet wood sits on the surface, peels within months, and wastes $150 to $400 of product. Test the wood before you stain: sprinkle a few drops of water on a board, and if the water beads up, the wood is still too wet or still has mill glaze; if the water soaks in within 10 seconds, the wood is ready. A $30 moisture meter gives a precise reading — stain when the wood reads below 15 percent moisture, and never stain above 20 percent. Cedar and redwood need a longer wait because they are naturally oily, and the surface needs 3 to 6 months of weathering before it will accept stain evenly.

The season matters as much as the wait. The best time to stain a fence is late spring or early fall, when daytime temperatures sit between 50 and 90 degrees Fahrenheit (10 to 32 degrees Celsius) and the humidity is below 70 percent. Stain applied below 50 degrees dries too slowly and stays tacky for days, collecting dust and pollen; stain applied above 90 degrees dries too fast, leaves lap marks, and does not penetrate the wood. Never stain in direct sun on a hot day — the surface of a dark fence can reach 120 degrees in July sun, and the stain will dry before it soaks in. Work on a cloudy day or stain the shaded side of the fence in the morning and the sunny side in the late afternoon. Check the forecast: the stain needs 24 to 48 hours without rain, and a fence stained 6 hours before a thunderstorm will wash off in streaks. An old fence that has never been stained should be cleaned and allowed to dry for 48 hours before you start, and a fence that is gray and weathered needs a wood brightener or a light sanding before the stain will take evenly.

Stain vs sealer vs paint: which finish is right for your fence?

A semi-transparent stain is the best finish for most wood fences, because it adds color, shows the wood grain, and protects against water and ultraviolet light for 3 to 5 years. Stain costs $30 to $60 per gallon and covers 150 to 300 sq ft per gallon on a rough-sawn fence, or 200 to 400 sq ft on a smooth fence. A transparent stain or clear sealer costs $25 to $50 per gallon, shows the most wood grain, and lasts only 2 to 3 years, because it has almost no pigment to block ultraviolet light. A solid stain costs $35 to $65 per gallon, hides the grain completely, looks like thin paint, and lasts 5 to 7 years — it is the best choice for an old fence with stains, mismatched boards, or gray weathering you want to cover. A clear water-repellent sealer costs $20 to $40 per gallon, protects against rain but not against sun, and needs reapplying every 1 to 2 years. Paint is the worst finish for a fence: it costs $30 to $50 per gallon, looks good for a year, and then peels in sheets, because paint forms a film on the surface instead of soaking into the wood, and a fence flexes with wind and temperature.

Oil-based stains penetrate deeper and last longer than water-based stains, but they take 24 to 48 hours to dry, smell strongly, and need mineral spirits for cleanup. Water-based stains dry in 4 to 6 hours, clean up with soap and water, and have almost no odor, but they do not penetrate as deeply and need reapplying 6 to 12 months sooner than an oil-based stain. For a cedar or redwood fence, an oil-based semi-transparent stain is the best choice, because it feeds the wood and brings out the color; for a pressure-treated pine fence, either type works, and water-based is easier for a first-timer. Choose the color carefully: a natural cedar tone suits most yards and never looks dated, a dark walnut or espresso stain hides dirt and makes the fence recede into the background, and a redwood tone warms up a pale pine fence. Avoid white or light-colored solid stains on a fence — they show every splash of mud and every mildew spot within a year. Buy one extra gallon beyond your calculation, because a fence always absorbs more stain than the label promises, especially on the first coat, and a gallon bought a month later may not match the batch.

How much does fence staining cost?

Staining a fence costs $700 to $2,000 professionally, or $150 to $400 do-it-yourself, for a typical 150 linear ft fence that is 6 ft tall. The professional price breaks down to $1.50 to $4 per linear foot for a 6 ft fence, or $0.75 to $2 per sq ft of fence surface, and the price includes cleaning, minor repairs, and two coats of stain. A 100 linear ft fence costs $500 to $1,200 professionally, a 150 linear ft fence costs $700 to $2,000, and a 200 linear ft fence costs $1,000 to $2,500. The price climbs when the fence is 8 ft tall instead of 6 ft, when the fence has two sides that both need staining, when the boards are rough-sawn and absorb more stain, and when the fence needs power washing or repairs first. A fence with peeling old stain that needs stripping costs $500 to $1,000 more, because stripping takes a full day of labor and a chemical stripper at $30 to $50 per gallon.

A do-it-yourself staining job costs $150 to $400 for the same 150 linear ft fence. Stain costs $30 to $60 per gallon, and a 150 linear ft fence that is 6 ft tall has about 900 sq ft of surface on one side, or 1,800 sq ft on both sides, so you need 4 to 8 gallons depending on whether you stain one side or both and how rough the wood is. A pump sprayer costs $30 to $60 and is the fastest way to apply stain, a 4 in brush costs $10 to $20, and a roller with a 3/4 in nap costs $15 to $25. Add $30 to $50 for a wood cleaner, $20 to $40 for a wood brightener, and $10 to $20 for drop cloths and painter's tape. Renting a pressure washer costs $40 to $75 per day if you do not own one. The labor is the real cost of a do-it-yourself job: cleaning takes 2 to 3 hours, staining one side takes 3 to 5 hours, and staining both sides takes 6 to 10 hours, so a full weekend is realistic for a 150 linear ft fence. The cheapest way to stain a fence is to do it yourself with a sprayer and a brush for the cut-in work; the most expensive mistake is hiring a professional who sprays one thin coat and leaves, because a single coat lasts half as long as two coats.

Close-up of a brush applying semi-transparent cedar-tone stain to a wooden fence board, showing the grain through the finish
Staining a fence costs $700 to $2,000 professionally, or $150 to $400 do-it-yourself: wait 4 to 6 weeks after installing pressure-treated wood, stain below 15 percent moisture, and reapply a semi-transparent stain every 3 to 5 years.

How do you stain a fence step by step?

Staining a fence takes 6 to 10 hours for a 150 linear ft fence, and the steps are: clean the fence, let it dry for 48 hours, protect the plants and the ground, apply the stain, and let it cure for 24 to 48 hours. Start by cleaning the fence with a wood cleaner and a pressure washer on a low setting — 1,500 to 2,000 PSI with a 25-degree fan tip — or a garden hose and a stiff brush if you do not own a pressure washer. A pressure washer held too close will gouge the wood, so keep the tip at least 12 in from the surface and move in smooth passes. Scrub any green algae or mildew with a mix of one part household bleach to three parts water, let it sit for 10 minutes, and rinse thoroughly. Let the fence dry for 48 hours in dry weather, and test the moisture with a meter or the water-drop test before you open the stain. Cover the plants along the fence with drop cloths, and lay a drop cloth on the ground, because stain kills grass and stains concrete permanently.

Apply the stain with a pump sprayer for speed and a brush for the finish: spray a 3 to 4 ft section at a time, then immediately back-brush the section with a 4 in stain brush to work the stain into the wood and eliminate drips and lap marks. Back-brushing is the step that separates a professional-looking job from a blotchy one — stain that is sprayed and left to dry pools in the low spots and dries unevenly, while stain that is brushed in penetrates the grain and dries to an even color. Work from the top of the fence to the bottom so drips run onto wet stain instead of dry stain, and stain one board at a time from end to end so you never stop in the middle of a board. Apply two thin coats rather than one thick coat: the first coat soaks into the wood, the second coat builds the color and the protection, and two thin coats last 2 to 3 years longer than one thick coat. Wait 4 to 6 hours between coats for water-based stain and 24 hours for oil-based stain. Clean the sprayer and brushes with water for water-based stain or mineral spirits for oil-based stain, and do not leave the stain can open in the sun. The most common mistake is staining in direct sun, which dries the stain before it penetrates and leaves lap marks — work on a cloudy day or follow the shade around the fence.

How often do you need to restain a fence?

Restain a fence every 2 to 3 years for a transparent stain, every 3 to 5 years for a semi-transparent stain, and every 5 to 7 years for a solid stain. The exact interval depends on the sun exposure: a fence in full southern sun fades twice as fast as a fence in shade, and a fence in a hot, dry climate needs restaining a year sooner than the same fence in a mild climate. A fence in the Pacific Northwest lasts longer between coats because the cloud cover blocks ultraviolet light, while a fence in Arizona or Texas fades fast because the sun is intense and the wood dries out. Test the fence every spring with the water-drop test: sprinkle water on a board, and if it soaks in within 10 seconds, the protection is gone and the fence needs restaining; if the water beads up, the finish is still working and you can wait another year. The test takes 10 seconds and saves you from staining a fence that does not need it or neglecting one that does.

Restaining is faster and cheaper than the first staining, because the wood is already sealed and the stain goes on more evenly. A restain of a 150 linear ft fence takes 4 to 6 hours and costs $100 to $250 in stain, because you need only 3 to 5 gallons instead of 4 to 8, and the cleaning is lighter — a quick wash with a wood cleaner and a rinse, rather than a full pressure wash. The one exception is a fence with peeling or flaking stain: peeling means the old finish has failed, and you need to strip it before you restain, which adds a full day of work and $100 to $200 in chemical stripper. Never stain over peeling stain — the new coat will peel with the old coat within months, and you will have wasted the product and the weekend. If the fence is gray and weathered but the stain has not peeled, a wood brightener restores the color before you restain, and the brightener costs $20 to $40 for a gallon that covers 500 sq ft. The rule is simple: a fence that is restained on schedule lasts 20 to 25 years, while a fence that is never stained rots in 10 to 15 years, so a $200 restain every 4 years is the cheapest fence insurance you will ever buy.

Common fence staining mistakes and how to fix them

The most common fence staining mistake is staining wood that is too wet: the stain sits on the surface, peels within months, and the only fix is to strip the fence and start over, which costs a full day and $100 to $200 in stripper. The second mistake is staining in direct sun or above 90 degrees Fahrenheit (32 degrees Celsius): the stain dries before it penetrates, leaves lap marks where each section overlaps, and the only fix is to sand the lap marks and restain the affected boards. The third mistake is applying one thick coat instead of two thin coats: a thick coat stays tacky, collects dust, and peels, while two thin coats penetrate and last 2 to 3 years longer. The fourth mistake is skipping the cleaning step: stain applied over dirt, algae, or mildew does not bond to the wood, and the finish fails within a year. Clean the fence, let it dry for 48 hours, and test the moisture before you open the stain can.

The fifth mistake is using a paint roller without back-brushing: a roller leaves a stippled texture on a fence and misses the gaps between boards, while a sprayer followed by a brush gives an even coat that penetrates the grain. The sixth mistake is staining only one side of a fence that you own: the unstained side weathers, grays, and rots faster, and the fence fails from the back while the front still looks good. If you share a fence with a neighbor, offer to stain their side too, or agree to split the cost — a fence stained on both sides lasts 5 to 10 years longer than a fence stained on one side. The seventh mistake is choosing a color from a tiny swatch: a stain color looks 2 to 3 shades darker on a full fence than it does on a 2 in sample, so test a full board in an inconspicuous spot and look at it in morning and evening light before you commit to 5 gallons. The final mistake is forgetting the posts and the caps: the tops of the posts absorb the most water, and a post cap or a coat of stain on the end grain adds 5 years to the life of a post. Stain the tops of the posts and the cut ends of every board, because end grain absorbs water 10 times faster than face grain, and the ends are where rot starts.

Frequently asked questions

Keep reading

Wood Fence Maintenance Guide: Cleaning, Staining and Repairs That Double Its Life

How-To

Wash yearly, stain every 2 to 3 years when water stops beading, fix posts before boards, and cap every post top — a maintained wood fence lasts 20 to 30 years, while the same fence untreated lasts 10 to 15.

Read the article