Article — How-To · November 8, 2026 · 15 min read
Deck Cleaning Guide: Washing, Stains and Prepping Wood for Sealer
Clean a wood deck once a year in spring with oxygen bleach at $15 to $25 a gallon, scrub with a stiff brush, keep a pressure washer at 500 to 600 PSI with a fan tip 12 inches from the boards, and let the wood dry 48 hours before sealing.
Clean a wood deck once a year in spring with a deck cleaner, a stiff-bristle brush, and a garden hose — a pressure washer is optional and only safe at 500 to 600 PSI with a fan tip held 12 inches from the boards. A standard 300 sq ft deck takes 2 to 3 hours to clean by hand, a gallon of oxygen-bleach deck cleaner costs $15 to $25 and covers about 200 sq ft, and the deck needs 48 hours of dry weather after cleaning before you can seal or stain it. Size the job with the Deck Calculator, measure the deck with the Square Footage Calculator, compare the cost of a new deck with the deck build cost guide, and finish the job with the deck staining and sealing guide once the wood is clean and dry.
How often should you clean a deck? The once-a-year rule and the signs that say now
Clean a wood deck once a year in spring, and clean a composite deck once a year in spring or fall, because a year of pollen, leaves, dirt, and foot traffic builds up into a gray film that holds moisture against the boards and feeds mold and mildew. A deck that is cleaned annually lasts years longer than a deck that is ignored: the dirt and organic matter that sit on the surface trap moisture, and moisture is what causes wood to rot, fasteners to rust, and composite boards to stain. Clean sooner if you see black or green patches of mold or mildew, if the deck feels slippery when wet, if there are dark stains under planters or doormats, or if the wood has turned gray and dull — gray wood is not damaged wood, it is wood that has been weathered by the sun, and a good cleaning will bring back much of the original color. Clean after a storm that drops leaves and debris on the deck, and clean before any sealing or staining project, because sealer applied over dirt peels off within months and stain applied over mold locks the mold under the finish.
The timing matters as much as the frequency. Spring is the best season to clean a deck, because the weather is mild, the deck has had all winter to accumulate grime, and the cleaning prepares the wood for the summer season when you will actually use it. Choose a stretch of 3 to 4 days with no rain in the forecast, temperatures above 50°F (10°C), and moderate humidity, because the cleaner needs time to work and the deck needs 48 hours to dry before you seal or stain it. Avoid cleaning in direct midday sun, because the cleaner dries on the surface before it can work, and the boards can dry unevenly and leave streaks — clean in the morning or on a cloudy day, and work in sections of about 100 sq ft at a time so the cleaner stays wet while you scrub. Fall cleaning is a good second pass for decks under trees, because leaves that sit on a deck all winter stain the wood and trap moisture, and a quick sweep and wash in October prevents the worst of it. A deck that is swept weekly and cleaned annually will look good for 20 to 25 years; a deck that is never cleaned will look tired in 5 years and need replacing in 15.
Choosing the right cleaner: oxygen bleach, chlorine bleach, and what to use on composite
Oxygen bleach is the best cleaner for most wood decks: it is a powder of sodium percarbonate that you mix with water, it costs $15 to $25 a gallon of mixed solution, it removes dirt, mold, and mildew without damaging the wood fibers, and it is safe for plants, pets, and the lawn below the deck. Mix it according to the label — usually 8 ounces of powder per gallon of warm water — spread it over a wet deck with a pump sprayer or a watering can, let it sit for 10 to 15 minutes without letting it dry, scrub with a stiff-bristle brush, and rinse thoroughly with a garden hose. Oxygen bleach will not lighten the wood the way chlorine bleach does, and it will not remove a gray weathered surface completely, but it will clean the deck safely and it will not kill the grass or the shrubs underneath, which is the most common complaint about deck cleaning. For a 300 sq ft deck, you will need about 1.5 gallons of mixed solution, which is roughly 12 ounces of powder — a 3-pound tub of oxygen bleach cleaner costs $20 to $30 and covers two or three cleanings.
Chlorine bleach is stronger but riskier, and it should be used only on a wood deck with stubborn mold or mildew that oxygen bleach did not remove. Mix 1 part household bleach to 4 parts water, apply it with a pump sprayer, let it sit for 10 minutes, scrub, and rinse thoroughly — and wear gloves, eye protection, and old clothes, because chlorine bleach burns skin and ruins fabric. Never use chlorine bleach on a composite deck, because it can fade the color and damage the surface, and never use it near plants, because the runoff will kill grass and shrubs within hours. Composite decks need a cleaner made for composite, usually a mild soap solution or a composite-specific cleaner that costs $15 to $20 a bottle — mix 1/4 cup of dish soap per gallon of water, scrub with a soft-bristle brush, and rinse. Never use a harsh chemical, a wire brush, or a high-pressure washer on composite, because the surface scratches easily and a scratch in a composite board is permanent. For cedar and redwood decks, use a cleaner made for softwoods, because these woods are softer than pressure-treated pine and a harsh cleaner or a stiff brush can raise the grain and leave the surface rough.
Pressure washing without damaging the wood: PSI, tips, and the 12-inch rule
A pressure washer is safe on a wood deck only at 500 to 600 PSI with a 25-degree or 40-degree fan tip held 12 inches from the surface, and anything above 1,500 PSI or closer than 6 inches will gouge the wood and leave permanent stripes. The most common pressure-washing mistake is using a 0-degree or 15-degree tip, which concentrates the water into a narrow jet that cuts into softwood like a knife — a single pass with a 0-degree tip can leave a groove 1/8 inch deep that will show through stain and sealer. Use a fan tip, keep the wand moving at a steady pace of about 1 ft per second, and hold it at a consistent 12-inch distance, overlapping each pass by 50 percent so you do not leave stripes. Work with the grain of the wood, not across it, because washing across the grain lifts the fibers and leaves the surface fuzzy. If you do not own a pressure washer, rent one for $50 to $75 a day, or skip it entirely — a garden hose and a stiff brush will clean a deck just as well, it just takes 30 minutes longer, and it cannot damage the wood.
Before you pressure wash, inspect the deck and fix what needs fixing, because a pressure washer will find every loose board, popped nail, and soft spot. Walk the deck and check for boards that flex, nails that have popped up, screws that have backed out, and soft spots that indicate rot — replace a rotten board now, because a pressure washer will blow the soft wood apart and leave a hole. Set any popped nails with a nail set and a hammer, or replace them with 3-inch deck screws, because a nail head sticking up 1/8 inch will catch the pressure washer tip and tear the board. Cover any nearby plants with a tarp, because even oxygen bleach runoff can stress plants, and move the furniture, the grill, and the planters off the deck — a pressure washer will strip paint off a metal chair and blast soil out of a planter. Test the pressure washer on a hidden board first, such as the underside of a step or a board under the grill, and check the result before you commit to the whole deck. If the test board shows fuzzy fibers or gouges, lower the pressure or increase the distance until the result is clean wood with no damage.
Always test a new cleaner on a hidden spot before you commit to the whole deck, because deck wood varies — pressure-treated pine, cedar, and redwood all react differently, and a cleaner that is safe on one can discolor another. Pick a board under a step or behind the grill, apply the mixed cleaner, wait 10 minutes, scrub, and rinse, then let it dry for an hour and look at the result in daylight: the wood should look cleaner and a little lighter, with no dark blotches, no raised grain, and no bleached patches. If the test spot looks bleached or fuzzy, dilute the cleaner by half and test again, or switch to a milder oxygen bleach formula. Keep the cleaner off the house siding and off any metal railings, because even oxygen bleach can leave streaks on painted siding and dull a metal finish — rinse any splashes immediately with a garden hose, and lay a drop cloth over stone or concrete below the deck if you are using a chlorine solution, because bleach runoff can stain concrete and kill grass within a day.
Removing stains: mold, mildew, grease, rust, and the gray weathered look
Black and green mold and mildew are the most common deck stains, and oxygen bleach removes them in most cases: mix the solution, apply it to a wet deck, let it sit for 15 minutes, scrub with a stiff-bristle brush, and rinse. If the mold is stubborn, apply a second coat and let it sit for 30 minutes, or use a chlorine bleach solution of 1 part bleach to 4 parts water on wood only, with gloves and eye protection. Mold grows where moisture sits, so the stain will come back unless you fix the cause — trim back any shrubs that block airflow, move planters off the deck or put them on feet so air circulates underneath, and sweep the deck weekly so leaves do not pile up and trap moisture. A deck that stays wet for more than 48 hours after rain will grow mold, so check the drainage: the deck should slope slightly away from the house, and the gaps between boards should be clear of debris so water drains through instead of pooling on the surface.
Grease stains from a grill, rust stains from metal furniture, and tannin stains from leaves each need a different approach. Grease comes off with a degreaser or a paste of baking soda and water scrubbed into the stain, left for 20 minutes, and rinsed — a grill mat under the grill prevents the next stain, and it costs $20 to $40. Rust stains from a metal chair leg or a planter need an oxalic acid wood brightener, which costs $10 to $15 a bottle: apply it to the stain, let it sit for 10 minutes, scrub, and rinse, and the rust will fade without bleaching the surrounding wood. Tannin stains from wet leaves are the brown blotches that appear after a rainy autumn — oxygen bleach removes most of them, and a wood brightener removes the rest. The gray weathered look is not a stain but a surface change: ultraviolet light breaks down the wood fibers on the surface and turns them gray, and a deck cleaner will lighten it but not remove it completely. To restore the original color, use a wood brightener after cleaning, or sand the deck lightly with 60-grit sandpaper on a pole sander, which removes the gray layer and exposes fresh wood underneath. A deck that has gone fully gray can usually be brought back to a warm brown with a cleaner, a brightener, and a fresh coat of stain.
Prepping the deck for sealer or stain: the 48-hour dry rule and the splash test
After cleaning, a wood deck needs 48 hours of dry weather before you can seal or stain it, because sealer applied to damp wood does not bond and peels off within months. The 48-hour rule is a minimum: in humid weather or on a deck that is shaded most of the day, wait 72 hours, and test the moisture with a simple splash test — sprinkle a few drops of water on the boards, and if the water soaks in within 5 seconds, the wood is dry enough to stain; if it beads up or sits on the surface, the wood is still too wet or the old finish is still there. If the water beads, the old sealer or stain has not been removed, and you need to strip it with a deck stripper or sand it off before the new finish will bond. Check the weather forecast for 3 days of dry weather with temperatures between 50°F and 90°F (10°C to 32°C), because stain applied in temperatures below 50°F does not cure properly, and stain applied above 90°F dries too fast and leaves lap marks.
Before you stain, do a final inspection and a light sanding. Walk the deck and check for rough spots, raised fibers, and splinters — a pressure washer and a stiff brush can raise the wood grain, and a quick pass with 60-grit sandpaper on a pole sander smooths it out in 30 minutes for a 300 sq ft deck. Sweep the deck thoroughly and blow off the dust with a leaf blower, because dust under stain shows up as bumps in the finish. Tape off the house siding and any metal railings with painter's tape, and lay a drop cloth over any concrete or stone below the deck, because stain drips are hard to remove from concrete. Apply the stain or sealer with a brush, a roller, or a pump sprayer followed by back-brushing, and work in sections of 2 to 3 boards at a time so you maintain a wet edge and avoid lap marks. A 300 sq ft deck needs about 2 gallons of stain at a coverage rate of 150 sq ft per gallon for the first coat, and a second coat needs about 1 gallon. Let the first coat dry for 24 hours before you walk on it, and wait 48 hours before you put the furniture back.
Keeping a deck clean all year: a simple maintenance schedule
A deck stays clean with 15 minutes of work a week and a deeper clean once a year, and the weekly work is what makes the annual clean easy. Sweep the deck once a week with a push broom to remove leaves, pollen, and dirt before they get ground into the boards by foot traffic — a deck that is swept weekly takes half the time to clean in spring, because the grime never gets a chance to build up. Move planters and doormats every few weeks, because anything that sits on the deck traps moisture underneath and leaves a dark stain that takes scrubbing to remove. Put planters on feet or on a saucer with drainage, so water does not pool under them, and put a grill mat under the grill to catch grease. In fall, sweep the deck after every big leaf drop, and do a final sweep and wash in October before the leaves sit all winter. In winter, use a plastic shovel to clear snow, never a metal shovel, because a metal edge gouges the wood, and avoid salt-based ice melt on a wood deck — use sand or a calcium chloride product labeled safe for wood, because rock salt dries out the wood and corrodes the fasteners.
Budget the maintenance as a real cost, because a deck that is maintained costs far less than a deck that is replaced. Annual cleaning costs $30 to $50 in supplies if you do it yourself — a gallon of oxygen bleach cleaner, a brush, and a few hours of your time — or $150 to $300 if you hire a professional to clean a 300 sq ft deck. Sealing or staining every 2 to 3 years costs $100 to $200 in materials for a 300 sq ft deck, or $400 to $800 hired out. A deck that is cleaned annually and sealed every 2 to 3 years lasts 20 to 25 years, while a deck that is never cleaned or sealed lasts 10 to 15 years before the boards rot and the structure needs replacing — and a new deck costs $15 to $35 per sq ft, which is $4,500 to $10,500 for a 300 sq ft deck. Put the annual cleaning on the calendar for the same weekend every spring, the weekend after the last frost is a good rule, and treat it like changing the oil in a car: a small, regular job that prevents a very expensive repair.
Frequently asked questions
Clean a wood deck once a year in spring, and clean a composite deck once a year in spring or fall. A deck that is cleaned annually lasts years longer than one that is ignored, because dirt and organic matter trap moisture against the boards and feed mold and mildew. Clean sooner if you see black or green mold, if the deck feels slippery when wet, or if there are dark stains under planters or doormats. Sweep the deck weekly and clean it before any sealing or staining project.
Yes, if you keep the pressure at 500 to 600 PSI, use a 25-degree or 40-degree fan tip, and hold the wand 12 inches from the surface. Anything above 1,500 PSI or closer than 6 inches will gouge the wood and leave permanent stripes. Never use a 0-degree or 15-degree tip on a deck, because the narrow jet cuts into softwood like a knife. Work with the grain at about 1 ft per second, overlap each pass by 50 percent, and test on a hidden board first. A garden hose and a stiff brush will clean a deck just as well if you do not own a pressure washer.
Oxygen bleach is the best cleaner for most wood decks: it is a powder of sodium percarbonate mixed with water, it costs $15 to $25 a gallon of mixed solution, it removes dirt, mold, and mildew without damaging wood fibers, and it is safe for plants, pets, and the lawn. Mix 8 ounces of powder per gallon of warm water, let it sit for 10 to 15 minutes, scrub with a stiff-bristle brush, and rinse. Chlorine bleach is stronger but riskier — use it only on wood with stubborn mold, never on composite, and never near plants.
A wood deck needs 48 hours of dry weather after cleaning before you can seal or stain it, and 72 hours in humid weather or on a shaded deck. Test with the splash test: sprinkle water on the boards, and if it soaks in within 5 seconds, the wood is dry enough; if it beads up, the wood is still wet or the old finish is still there. Check the forecast for 3 days of dry weather between 50°F and 90°F, because stain applied below 50°F does not cure properly and stain applied above 90°F dries too fast and leaves lap marks.
Black mold stains come off with oxygen bleach in most cases: apply the solution to a wet deck, let it sit for 15 minutes, scrub with a stiff-bristle brush, and rinse. For stubborn mold, apply a second coat for 30 minutes, or use a chlorine bleach solution of 1 part bleach to 4 parts water on wood only, with gloves and eye protection. Fix the cause as well as the stain: trim shrubs that block airflow, put planters on feet so air circulates underneath, and sweep weekly so leaves do not pile up and trap moisture.
Keep reading
Deck Staining and Sealing: When to Restain, What It Costs, and How to Make It Last
How-ToRestain a wood deck every 2 to 3 years, or when water stops beading on the surface — a 300 sq ft deck costs $300 to $700 DIY or $700 to $1,500 professionally, and preparation is most of the job.
Read the article